Solare Datensysteme Solar-Log Components Connection Manual Download | Manualshive

Page: 408 / 506

background image

408

General Information on Wiring

3.3.2

Meter connection options for bi-directional recording of the total

consumption via only an RS485 interface.

If there is feed-in in a sub-distribution, the option mentioned above can be used. In this
case, the the amount of feed-in power and power obtained from the grid can be recorded with a bi-directional
meter. With this,
the Solar-Log™ can calculate the consumption.

Fig.: Wiring diagram for recording self-consumption – bi-directional meter. (optional with battery storage)

Important information on possible options when using meters for recording consumption:

•

Bi-directional meters (only via RS485) in the operating mode „Consumption meter (bi-directional):“ It is only
possible to have one meter per Solar-Log™ device. Additional meters are only possible as „sub-consumption
meters.“

•

Uni-directional meters (RS485 or S0) in the operating mode „Consumption meter:“
It is possible to have several meters connected to a single Solar-Log™ device as consumption meters – the
consumption value is totaled together. Additional meters are also possible in the „Consumption meter“ opera-
ting mode.

•

Meters in the „Consumption meter“ operating mode are used to display the consumption values from indivi-
dual appliances. These consumption values have already been recorded in the total consumption values by
the uni- and bi-directional meters.

«
...
406
407
408
409
410
...
»

Summary of Contents for Solar-Log



























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Solar-Log

PR1000IS Series

Brand: MadgeTech Pages: 4

Brand: Shenzhen JZC Telecom Technology Pages: 7

Brand: Nivus Pages: 60

Brand: YSI Pages: 6

Video Investigation Portable

Brand: SalvationData Pages: 37

Brand: Fluke Pages: 173

Brand: Racepak Pages: 124

Brand: YDOC Pages: 45

Brand: GRAPHTEC Pages: 22

Brand: Danelec Pages: 27

Brand: Danelec Pages: 36

Brand: Ijinus Pages: 20

Brand: Omega Engineering Pages: 256

EasyLog EL-EnviroPad-TC

Brand: Lascar Electronics Pages: 2

Brand: Neptune Technology Pages: 52

Brand: VOLTCRAFT Pages: 156

Brand: VOLTCRAFT Pages: 232

Brand: Rotronic Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands