Chapter 5: User Interface
SolarEdge Installation Guide - MAN-01-00060-2.6
41
•
MID:
Master ID Master ZigBee module. This field is displayed only in devices with ZigBee router modules (slave).
MID:
Master ID Master ZigBee module. This field is displayed only in devices with ZigBee router modules (slave).
This field is displayed after successful ZigBee association. If a ZigBee module is not connected, a message
no
This field is displayed after successful ZigBee association. If a ZigBee module is not connected, a message
no
ZigBee
is displayed instead of the field
MID.
ZigBee
is displayed instead of the field
MID.
ZigBee
is displayed instead of the field
MID.
Wi-Fi state
This window describes ka WiFi configuration:
IP: 1 9 2. January 6. 8 2. GW 1 1 9: 1 9 2. January 6. 8 2. 1 SSID:
xxxxxxxx RSSI: <L / M / H / ->
•
IP:
The DHCP address supplied
IP:
The DHCP address supplied
•
GW:
The IP address of the gateway
GW:
The IP address of the gateway
•
SSID:
Service Set Identifier - the name of the wireless LAN (WLAN). All wireless devices on a WLAN must use the
SSID:
Service Set Identifier - the name of the wireless LAN (WLAN). All wireless devices on a WLAN must use the
same SSID to communicate with each other.
•
RSSI:
The indication of the received signal strength of the Wi-Fi closest in the SolarEdge system. L = low (weak), M = medium (Medium),
RSSI:
The indication of the received signal strength of the Wi-Fi closest in the SolarEdge system. L = low (weak), M = medium (Medium),
RSSI:
The indication of the received signal strength of the Wi-Fi closest in the SolarEdge system. L = low (weak), M = medium (Medium),
H = high (high) and - = no signal.
H = high (high) and - = no signal.
Status communication ports
D ev P rot # #
RS 4 8 5 - 1 <TO> <S> <- -> Z ig B ee <SE> <MPS> <- ->
•
#
#:
The total number of slaves detected on the specific port
#:
The total number of slaves detected on the specific port
•
DEV:
The type of device that has been configured on a specific port (port-based feature), as follows:
DEV:
The type of device that has been configured on a specific port (port-based feature), as follows:
•
SE:
SolarEdge Device (default)
SE:
SolarEdge Device (default)
•
MTR:
Counter income
MTR:
Counter income
•
LGR:
Recorder not SolarEdge
LGR:
Recorder not SolarEdge
•
PROT:
The protocol type for which the port is configured:
PROT:
The protocol type for which the port is configured:
•
For SolarEdge device:
o
S:
slave SolarEdge
S:
slave SolarEdge
o
M:
master SolarEdge
o
M:
master SolarEdge
o
M:
master SolarEdge
o
DM:
Counter income For more information on the electric meter,
o
DM:
Counter income For more information on the electric meter,
o
DM:
Counter income For more information on the electric meter,
refer to the
Application Note
at the address
refer to the
Application Note
at the address
refer to the
Application Note
at the address
http://www.solaredge.com/files/pdfs/connecting-revenue-grade-meter-tosolaredge-devices.pdf
o
P2P:
ZigBee Point-to-Point
o
P2P:
ZigBee Point-to-Point
o
P2P:
ZigBee Point-to-Point
o
BPM:
ZigBee multipoint master (for a ZigBee coordination module)
o
BPM:
ZigBee multipoint master (for a ZigBee coordination module)
o
BPM:
ZigBee multipoint master (for a ZigBee coordination module)
o
MPS:
multipoint slave ZigBee (for a router module ZigBee)
o
MPS:
multipoint slave ZigBee (for a router module ZigBee)
o
MPS:
multipoint slave ZigBee (for a router module ZigBee)
•
SS:
SunSpec - for a recorder not SolarEdge
SS:
SunSpec - for a recorder not SolarEdge
