background image

5

en

1  Notes on the manual

1�1 

Scope

The scope of this manual is to provide detailed instructions about the instal-

lation, operation, maintenance and troubleshooting procedures for the fol-

lowing SOLARMAX inverters: 3600SP / 4000SP / 4600SP / 5000SP

1�2 

Target groups

This instruction manual is intended for the operator of the plant and the 

installer of the PV power plant. Before any action is taken, the user must first 

read the safety instructions to protect himself from the hazards deriving from 

using devices operating at high voltages.

Electrical connection an installation may only be carried out by trained elec-

tricians (e.g. electricians, electric systems technicians, electrical mechanics, 

and industrial electronics technicians).

1�3 

Where to keep this manual

The plant operator must ensure that this instruction manual is available to the 

relevant persons at all times. If this original document is lost, an up-to-date 

version of this instruction manual can be downloaded from our website at any 

time (

www.solarmax.com

).

1�4 

Symbols used

The following safety instructions and general information are used within this 

instruction manual.

DANGER!

Non-observance of these safety instructions results in serious inju-

ries or death. 

WARNING!

Non-observance of these safety instructions may result in serious 

injuries or death.

CAUTION!

Non-observance of these safety instructions may result in minor or 

extensive injuries.

ATTENTION!

Non-observance of these safety instructions may result in material 

damage.

Note
Notes contain additional information or facilitate operation of the 

inverter.

Summary of Contents for 10094601





































Reviews: