background image

19

7  Technical data

Number of measured val-
ues that can be shown

3

Display elements

7-segment LED fields with 45 mm high characters, 
Color: red

Resolution per measured 
value

watts, 5 places, up to 99999 max.
kWh, 6 places, up to 999999 max.
kg, 6 places, up to 999999 max.

Housing dimensions

W x H x D: 800 x 600 x 50 mm

Housing material

Front plate: Single-pane safety glass, 5 mm
Housing: aluminum, plastic

Operating temperature

0 to + 40 °C, with "outdoor" option - 15 to + 50 °C

Storage and transport 
temperature

- 20 to + 60 °C

Supported data sources
(depending on configura-
tion, data source must be 
indicated with order!)

- Pulse generator (floating make-contact)
- SMA Sunny Boy Control Standard, Light and Plus
- Suntrol 200/400 and 800
- various other systems on request

Inputs, interfaces

-  Pulse (for floating make-contact, minimum pulse 

length: 2 ms)

- RS-232
- RS-485

Power supply

External power supply: 
Input: 230 V AC, Output: 12 V DC, 1 A

Never connect display directly to the 230-V AC grid 
or voltages greater than 12 V DC: may cause danger, 
damage or fire!

Warranty

2 years

Standards

CE

Subject to change, technical or otherwise

Summary of Contents for Suntrol STD800LED





















Reviews: