11
1. Match up the Connecting Arm Covers (87 & 88) and install onto the Left and
Right Connecting Arms (8 & 9) and secure each side with one Sheet Metal
Screw (126) and two Phillips head screws (115) by using the Short Phillips
Head Screw Driver (160). Make sure these covers are positioned in relation to
the arrow on each sticker.
2. Install Sliding Wheel Covers (82) on each side and secure with four Phillips
Head Screws (115).
3. Install the two middle Stabilizer Covers (93) and (94) on the middle stabilizer
bar with Phillips Head Screws (115).
4. Install the Front Stabilizer Cover (79) on the front stabilizer with two Phillips
Head Screws (115).
5. Install the two incline Cover brackets (21), with the hole for mounting the
plastic cover on the bent tab facing rearward, and secure them on the Incline
Rail Assembly with four Phillips Head Screws (125). Install the Rear Incline Bar
Cover (91) on the rail base with two Screws (115).
6. Install the Rear Stabilizer Cover (92) on the Rear Stabilizer with four Phillips
Head Screws (115).
7. Match up the console covers (95 & 96) and secure with three Phillips head
screws (115) and two Sheet metal screws (126). Tighten the Sheet metal
screws 1st.
8. This step to be performed after the elliptical power is plugged in. Elevate
the incline to Level 8 and install the incline Rail Front Cover (89) up against
the Middle Stabilizer tube with two Phillips Head Screws (115) Tighten with
PLASTIC PARTS
4
HARDWARE STEP 4
1. 1. Untie the wire holding the Sleeve Spacer (19) in place on the rod-end
of the Connecting Arms (8 & 9). Align the hole in the rod ends with the hole
in the brackets of the left and right Handle Bar (10 & 11). The end of
connecting arms should be positioned on the inside of the Handle Bar
bracket. Secure with a Hex Head bolt (109), Flat Washer (157) and Nylon Nut
(137) by using the Wrenches provided (159 & 162).
CONNECTING ARM
3
HARDWARE STEP 3
See Page 12 for Illustration
See Page 12 for Illustration
#157. 5/16” x 20 x 1.5T
Flat Washer (2 pcs)
#137. 5/16” x 7T
Nylon Nut (2 pcs)
#109. 5/16” x 1-1/4”
Hex Head Bolt (2 pcs)
#126. 3.5 x 12mm Sheet
Metal Screw (4 pcs)
#115. M5 x 15mm
Phillips Head Screw
(23 pcs)
#125. M6 x 10mm
Phillips Head Screw
(4 pcs)
E25 / E35 ELLIPTICAL
Wrench (161).
Summary of Contents for E25
