background image

                                                         

 

 

SOLE S.A.  –  Solar Collectors  –  Installation Manual 

 

16

6. Tile roof installation 
 
The assembly of solar collectors on a tile roof is done in a manner similar to that 
described above, with a different position of the vertical legs A3 that have to be 
placed horizontally underneath the E1/E2 in a parallel manner. The crosspieces X1 
or X2 and X3 shorts are not needed for tile roof installation. 
 
The profiles D3 longitudinal and transverse E1 or E2 have to be fixed to the roof with 
strength and without compromising its tightness. The fixing procedure will depend on 
the characteristics of the roof. With the installation fittings are supplied some 
perforated flexible metal strips to facilitate this fixation on certain roof configurations. 
(See fig. 19) The collectors and the support system can withstand wind velocity up to 
120km/h and weight of snow up to 80cmheight at 45 degrees. 
 

 

 

Figure 19. 

 
 
 
 
7. Connections and Hydraulic Circuit 
 
The collectors or different groups of solar collectors must be connected hydraulically 
to form a closed primary solar collection circuit. The use of copper pipes is 
recommended, with a wall minimum thickness of 1 mm and an adequate diameter for 
the circulation flow of each part.  
 
The entry of liquid to the group of solar collectors will be from the end at the bottom 
of the collector. On the top end connection a plug must be installed. The output of 

Summary of Contents for 1,75























Reviews: