Solid RocketWAVE SRF-L-8A1821 Product Manual Download

Page: 4 / 25

SOLiD RocketWAVE™ SRF-L-8A1821 Product Manual

V1.7 - DEC 2021

Page 4

General

“Only qualified personnel are allowed to handle this unit. Read carefully and understand all the warning

labels attached in this user manual”. Any personnel involved in installation, operation or service of the

SOLiD repeaters must understand and comply the following:



Understand all general and regional installation and safety regulations relating to work on high voltage

installations, as well as regulations covering correct use of tools and personal protective equipment.



The power supply unit in repeaters contains dangerous voltage level, which can cause electric shock.

Switch the mains off prior to any work in such a repeater. Any local regulations are to be followed when

servicing repeaters.



The repeater cover should be (door) securely fastened in open position, e.g. by tying it up, at outdoor work

in order to prevent door from slamming due to wind causing bodily harm or damage.



Use this unit only for the purpose specified by the manufacturer. Do not carry out any modifications or fit

any spare parts which are not sold or recommended by the manufacturer. This could cause fires, electric

shock or other injuries.



Any repeater, including this repeater, will generate radio signals and thereby give rise to electromagnetic

fields that may be hazardous to the health of any person who is extensively exposed to the signals at the

immediate proximity of the repeater and the repeater antennas.



Due to power dissipation, repeater may reach a very high temperature. Do not operate this unit on or close

to flammable materials.



Do not use any solvents, chemicals, or cleaning solutions containing alcohol, ammonia, or abrasives.



For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily ac-

cessible.



This power of this system shall be supplied through wiring installed in a normal building. If powered directly

from the mains distribution system, it shall be used additional protection, such as overvoltage protection

device.



Round terminals located on the rear of a 1.0mm2 (16AWG) or more wires using permanently connected

to earth.

CAUTIONS



This is a class B product. In domestic environment, this product may cause radio interference in which

cause the user may be required to take adequate measures.



Do NOT open except at Approved Field Force Protective Work Station

Summary of Contents for RocketWAVE SRF-L-8A1821























Search results

Summary of Contents for RocketWAVE SRF-L-8A1821

Reviews:

Related manuals for RocketWAVE SRF-L-8A1821

Brands by name

Popular brands

Solid RocketWAVE SRF-L-8A1821, Product Manual

Search results

Summary of Contents for RocketWAVE SRF-L-8A1821

Reviews:

Related manuals for RocketWAVE SRF-L-8A1821

Brands by name

Popular brands