Keys to Assembly Success
Part Identification Key
On each page, you will find the parts and
quantities required to complete the assembly
step illustrated on that page. Here is a sample.
Symbols
Throughout these instructions symbols are provided as important reminders for proper and safe assembly.
Proper Hardware Assembly
Lag screws require drilling pilot
holes to avoid splitting wood. Only
a flat washer is required. For ease of
installation liquid soap can be used
on all lag-type screws.
For bolts, tap T-Nut into hole with
hammer. Insert the hex bolt through
lock washer first then flat washer then
hole. Because the assemblies need to
be squared do not completely tighten
until instructed. Pay close attention to
diameter of the bolts. 5/16” is slightly
larger than 1/4”.
Once the assembly is tightened, watch for exposed
threads. If a thread protrudes from the T-Nut, remove the
bolt and add washers to eliminate this condition. Extra
washers have been provided for this purpose.
This identifies information that requires special
attention. Improper assembly could lead to an
unsafe or dangerous condition.
Where this is shown, 2 or 3
people are required to safely
complete the step. To avoid
injury or damage to the
assembly make sure to get help!
Check that assembly is square
before tightening bolts.
Use a measuring tape to assure
proper location.
Check that set or assembly is properly level
before proceeding.
Pre-drill a pilot hole before
fastening screw or lag to prevent
splitting of wood.
This indicates time to tighten bolts, but
not too tight! Do not crush the wood.
This may create splinters and cause
structural damage.
Use
Help
Use
Help
Measure
Distance
Square
Assembly
Use
Level
Pre-drill
1/8” Bit
Tighten
Bolts
No
Yes
CAUTION
– Protrusion Hazard
Tools Required
6
Shovel
Level
#2 & #3 Phillips
or Robertson
Safety
Glasses
Drill (1/8”
3/16” Bit)
Measuring
Tape
Hammer
Ratchet 1/2”,
7/16” & 9/16”
Square
Ruler
Step
Ladder
Flat
Washer
T-Nut
(Hammer into place)
Do not crush wood!
Lock
Washer
Hex Bolt
Bolt Assembly
If Bolt protrudes
beyond T-Nut
Use an extra
Flat Washer
Flat Washer
Lag Screw
Lag Assembly
Before mounting Lag Screws,
use factory drilled holes as
guides to drill 1/8” pilot holes.
Quantity
Key Number
2X A1 Post 2 x 4 x 83”
Part Description, Part Size
Summary of Contents for F23465
