6
7
Y
our Canopy Rangehood features push button controls (Fig. 1) with three speed levels of extraction.
INSTALLATION REQUIREMENTS
Typical installation tools required
You’ll most likely require the following tools/equipment
(not supplied) for the installation of your rangehood.
– Electrical drill
– Tape Measure
– Screw-driver
– Spirit Level
If ducting your rangehood, you’ll also most likely require:
– Jig saw
– Ladder
– Duct-tape
– Ducting
Important installation safety notes:
– Always switch the power off prior to beginning the installation.
– Stainless steel is very easily damaged during installation.
Wherever possible, protect the rangehood with the cardboard
box or plastic
wrap during the installation.
– For safety reasons, this Rangehood must be earthed.
– A power point must be located within 1.5m of the power cord exit
from the rangehood, and it should be always accessible to allow
isolation from power during cleaning or maintenance.
– A 150mm round ducting adapter is supplied, however all other
ducting accessories are not.
– All ducting must comply with building codes and local
requirements.
– If you are re-circulating the air, rather than ducting, please ensure
that the side outlet grilles are not obstructed in any way as this
will affect the efficiency of the rangehood.
– Ensure that the rangehood is mounted in a level position,
both horizontally and vertically. This is essential to ensure the
rangehood operates correctly and prevents grease build up at
one end.
Lo
w
Mi
d
H
ig
h
Li
gh
t
Stop Lo
w
Mi
d
H
ig
h
Li
gh
t
Stop Lo
w
Mi
d
H
ig
h
Li
gh
t
Stop
WARNING!
All electrical work associated
with the installation of this
rangehood must be carried out
by a licensed electrician. This
rangehood must be correctly
installed by a suitably qualified
person in strict accordance with
all applicable rules and regulations
and following the instructions in
this manual.
—
Do not try to install
the rangehood yourself; doing so
will expose you to danger and void
the warranty. Improper installation,
adjustment, alteration or service
can cause injury or damage.
We decline any responsibility for
in jury or damage, to persons or
property, as a result of improper
installation.
Fig. 1
CONTROLS
– Push the ‘Low’ button, and
the rangehood will
operate at
low speed.
– Push the ‘Mid’ button,
and the rangehood will
operate at a medium speed.
– Push the ‘High’ button, and
the rangehood will
operate at
a high speed.
– Push the ‘Light’ button and
the two lights will come on. To
turn the lights off, simply push
the ‘Light’ button again.
–
To switch the rangehood
motor or light off, simply press
the stop
button a second time.
It’s important to carefully read
the following installation
instructions before beginning
the installation of your
rangehood.
8
Ducting options
Before beginning the installation of your
rangehood, the method of ducting should be
considered and selected. The guide below
illustrates the various ducting options.
Note:
This rangehood can be operated in recirculation
mode where required, although it is
recommended to duct wherever possible.
— Straight up and through your tiled or metal
roof. (Fig. 2)
— Into your ceiling cavity and then vented
through your eaves. (Fig. 3)
— Through your wall (Fig. 4)
Further to your various ducting options,
below are some tips on how to correctly duct
your rangehood:
– Always use correctly sized ducting:
DO NOT reduce the size of the ducting
– Always use solid ducting
– Always use non-flammable ducting
– Always duct to the outside atmosphere
– Do not use flexible ducting
– Do not duct into the ceiling space:
always vent to the outside atmosphere.
– Avoid sharp 90 degree bends as much
as possible, use 45 degree bends instead
wherever possible
– Duct to the outside atmosphere using the
shortest duct run possible
– Use cylindrical ducting whenever possible
Positioning the rangehood:
Installation heights
– Over gas and electric cookers, we
recommend our rangehoods to be mounted
at a height of between 600-800mm above
the cooking surface.
– Electric cooktops must have a minimum
height of 600mm from the underside of the
rangehood to the cooktop face.
– Gas cooktops must have a minimum of
650mm from the burner to the underside
of the rangedhood.
– Gas Regulations require the fi lters of the
rangehood to be at least 1200mm above the
cooking surface when used over open flame
grillers or barbecues.*
* We do not recommend this rangehood
for outdoor use or being installed above
barbecues/open flame grillers.
Fig. 3
Fig. 4
Fig. 2
Controls
