Solwise 3G11nMRW User Manual Download

Page: 200 / 257

Version 1.0.15

200

Beacon Interval

Beacons are packets sent by an access point to synchronize a wireless network. Specify a

beacon interval value. The allowed setting range is 20 -1024 ms.

Preamble Type

The preamble (also called “a header”) is a section of data at the head of a packet that

contains information that wireless devices need when they send and receive packets. Short

preambles improve throughput performance, but some wireless devices require long

preambles. Select the suitable preamble as short or long preamble.

IAPP

Inter Access Point Protocol. Allow seamless roaming between Access Points in your

wireless network. Coupled with superior RF performance

Protection

Select to enable the wireless protection or not.

Aggregation

Data aggregation can reduce the amount of data routed through the network, and increasing

throughput.

Short GI

Enabling the Short Guard Interva l increases the wireless transmission.

RF Output Power

User can adjust the RF output power to get the best wireless connection. There are 5 power

types available: 100%, 70%, 50%, 35%, and 15%.

10. Apply Changes & Reset

Click on “

Apply Changes

” to save the setting data. Or you may click on “

Reset

” to clear all

the input data.

7.2.3

Wireless Site Survey

This function provides users to search existing wireless APs or wireless base stations from

ISP. You can connect to a wireless AP manually in WiFi AP mode. The design ed AP will

appear on SSID column in Wireless Basic Setup page.

Summary of Contents for 3G11nMRW


































































































































































































































































Search results

Summary of Contents for 3G11nMRW

Reviews:

Related manuals for 3G11nMRW

Brands by name

Popular brands

Solwise 3G11nMRW, User Manual

Search results

Summary of Contents for 3G11nMRW

Reviews:

Related manuals for 3G11nMRW

Brands by name

Popular brands