Solwise 3G11nMRW User Manual Download

Page: 212 / 257

Version 1.0.15

212

Enable Anonymous to Login

Allow anonymous to log in aft er check on enable.

FTP Server Port

Define the FTP command transfer service port. If you want to change this port number, also

remember to change the service port setting of your FTP client. The default is 21.

Idle Connection Time-Out

When a specific time value is added, FTP Server will be de -activated if it has no activity within

the time limit. The default is 300 seconds; the minimum is 60 seconds.

Apply Change & Reset

Click on

Apply Changes

to save the setting data. Or you may click on

Reset

to clear all the

input data.

Note: FTP server is compatible with FAT32 or EXT3 format USB storage device. In case you need to format your

USB storage device. Please always make sure the device is formatted with FAT32 or EXT3 standard.

7.3.3

Webcam Server

3.5G plus 11n Mobile Server Router has built -in Web Cam Server. By connecting web

camera to the router, it allows user to monitor their home or office from remote locations.

Motion Detection

function has also been built -in and allows user to use webcam to detect

any movements in their houses or offices and send email alert with captured images.

7.3.3.1

Webcam Server Basic Setting

Enable Webcam Server

Allow using this function by checking on enable.

Image format

Summary of Contents for 3G11nMRW


































































































































































































































































Search results

Summary of Contents for 3G11nMRW

Reviews:

Related manuals for 3G11nMRW

Brands by name

Popular brands

Solwise 3G11nMRW, User Manual

Search results

Summary of Contents for 3G11nMRW

Reviews:

Related manuals for 3G11nMRW

Brands by name

Popular brands