Solwise 3G11nMRW User Manual Download

Page: 227 / 257

Version 1.0.15

227

Enter the User Name.

New Password

Enter the new password you want to change.

New Password (Confirm)

Enter the new password again for confirming.

Apply Change & Reset

Click on

Apply Changes

to save the setting data. Or you may click on

Reset

to clear all the

input data.

Note: 1. Only the password can be changed, the user name for administrator is

admin

and not to be changed.

2. If you forget administrator’s password, please reset 3.5G plus WLAN Mobile Server Router to default setting by
pressing the “

Reset

” button on the rear panel o ver 5 seconds. And the password will return to

admin

7.4.2

Upgrade Firmware

There is certain risk while upgrading firmware. Upgrading firmware is not recommended

unless the significant faulty is found. You can upgrade the firmware of 3.5G plus 11n Mobile

Server Router on this page. Make sure the firmware you want to use is on the local hard drive

of the computer. Click

Upgrade Firmware

to proceed.

Update Firmware

Click on

Browse…

button to search your local hard drive and locate the firmware to be

used for update.

Upload & Reset:

Click

Upload

to upgrade the firmware or

Reset

to restore to factory default Settings

Note: 1. To prevent the firmware upgrading interrupted by other wireless signals and caused failure. We

recommend using wired connection to do the upgrading.
2. Before upgrading the firmware, please remove any USB device which connected with this router.
3.

The firmware upgrade will not remove your previous settings.

Summary of Contents for 3G11nMRW


































































































































































































































































Search results

Summary of Contents for 3G11nMRW

Reviews:

Related manuals for 3G11nMRW

Brands by name

Popular brands

Solwise 3G11nMRW, User Manual

Search results

Summary of Contents for 3G11nMRW

Reviews:

Related manuals for 3G11nMRW

Brands by name

Popular brands