Solwise 3G11nMRW User Manual Download

Page: 247 / 257

Version 1.0.15

247

Q: Why can't I connect to the router's configuration utility?

A: Possible Solution 1: Make sure that your Ethernet connect properly and securely.

Make sure that you've plugged in the power cord.

Possible Solution 2: Make sure that your PC i s using an IP address within the range

of 192.168.1.2 to 192.168.1.254. Make sure that the address of the subnet mask is

255.255.255.0. If necessary, the Default Gateway data should be at 192.168.1.1. To

verify these settings, perform the following steps:

Windows 95, 98, or My Users:

1. Click on Windows

Start

> click on

Run

> input

winipcfg

> click on

button.

2. Check the IP Address, Subnet Mask, Default Gateway data. Is this data

correct? If the data isn't correct, click on

Release All

. Then click on

Renew All

Windows NT, 2000, or XP Users:

1. Click on Windows

Start

> click on

Run

> input

cmd

> click on

button.

2. At the DOS prompt, type ipconfig/all.

3. Check the IP Address, Subnet Mask, Default Gateway data. Is this data

correct? If the data isn't correct. Pleas e input

ipconfig/release

> press

Enter

input

ipconfig/renew

> press

Enter

Possible Solution 3: Verify the connection setting of your Web browser and verify

that the HTTP Proxy feature of your Web browser is disabled. Make these

verifications so that your Web browser can read configuration pages inside your

router. Launch your Web browser.

Internet Explorer Users:

1. Click on

Tools

Internet Options

Connections tab

2. Select

never dial a connection

, click on

Apply

button, and then click on

button.

3. Click on

Tools

and then click on

Internet Options

4. Click on

Connections

and then click on

LAN Settings

5. Make sure none of the check boxes are selected and click on

button.

6. Click on OK button.

Netscape Navigator Users:

1. Click on

Edit

Preferences

> double-click

Advanced

in the Category window.

2. Click on

Proxies

> select

Direct connection to the Internet

> click on

button.

3. Click on

Edit again

and then click on

Preferences

Summary of Contents for 3G11nMRW


































































































































































































































































Search results

Summary of Contents for 3G11nMRW

Reviews:

Related manuals for 3G11nMRW

Brands by name

Popular brands

Solwise 3G11nMRW, User Manual

Search results

Summary of Contents for 3G11nMRW

Reviews:

Related manuals for 3G11nMRW

Brands by name

Popular brands