Solwise 3G11nMRW User Manual Download

Page: 248 / 257

Version 1.0.15

248

4. Under category, double-click on

Advanced

and then click on

Proxies

5. Select

Direct connection to the Internet

and click on

button.

6. Click on

button.

Web page hangs, corrupt downloads, or nothing but junk characters is being

displayed on the screen. What do I need to do?

A: Force your NIC to 10Mbps or half duplex mode, and turn off th e "Auto-negotiate"

feature of your NIC as a temporary measure. (Please look at the Network Control

Panel, in your Ethernet Adapter's Advanced Properties tab.)

Q: Why can't I connect to the Web Configuration?

A: you can remove the proxy server settings in your web browser.

9.5

3.5G plus 11n Mobile Server Router Setup

Q: Why does 3.5G plus 11n Mobile Server Router’s setup page shut down

unexpectedly?

A: If one of the pages appears incompletely in 3.5G plus 11n Mobile Server Router’s

setup pages, please click on Logout item on the Main Menu before shutting it down.

Don’t keep it working. Then, close Internet browser and open it again for going back

to the previous page.

Why can’t my USB devices and LAN ports work properly after setting the

DHCP?

A: There are two rules over here.

Rule1: After connecting USB devices, please reboot your Router.

Rule2: Before finishing the DHCP setup, please don’t connect any computer to LAN

ports, because the conflict of having the same IP may occur and cause some

computers a lot of trouble.

※

Notice: Make sure that you always click on the Apply button after configuring

each setting. And in order to let other LAN ports work properly, please reboot

your PC.

I don’t know how to configure DHCP.

A: DHCP is commonly used in the lar ge local network. It allows you to manage and

distribute IP addresses from 2 to 254 throughout your local network via 3.5G plus

Summary of Contents for 3G11nMRW


































































































































































































































































Search results

Summary of Contents for 3G11nMRW

Reviews:

Related manuals for 3G11nMRW

Brands by name

Popular brands

Solwise 3G11nMRW, User Manual

Search results

Summary of Contents for 3G11nMRW

Reviews:

Related manuals for 3G11nMRW

Brands by name

Popular brands