Solwise 3G11nMRW User Manual Download

Page: 36 / 257

Version 1.0.15

You can see a list of available Wireless networks. Select you preferred one to connect and

the Encryption type form the drop -down list.

4.2.3.4

WAN Access Type – Static IP

Choose Static IP Address if all WAN IP information is provided to you by your ISP. You will

need to enter the IP address, IP Netmask and IP gateway as provided. Each entered fields

must be in the appropriate IP form, which are four IP octets separated by a dot (x.x.x.x). The

Router will not accept the IP address if it is not in this format. Fill in t he DNS information

provided by your ISP; otherwise,

Domain Name

can’t be used.

In particular, here provides 3G or 3.5G transmission rate when the 3.5G adapter is plugged,

just check to apply for the backup. In other words, once Static IP connection is disc onnected,

the system automatically connects Internet via 3.5G adapter. If 3.5G signal is not available, it

starts to search downward for 3/2.75/2.5G signals until none existed. The default interval

between the two connection detection is 3 minutes. The int erval range is from 1 to 60

minutes.

The 3.5G feature is working as mutual backup for other 3 WAN Types, and the required

information is listed as follows, such as user name, password and SIM PIN etc. That is,

setting up the interval time to auto detect wh ether the Internet connection is lost or not. If yes,

the system immediately switches to 3.5G Internet connection and will not switch back to the

original Static IP connection.

Summary of Contents for 3G11nMRW


































































































































































































































































Search results

Summary of Contents for 3G11nMRW

Reviews:

Related manuals for 3G11nMRW

Brands by name

Popular brands

Solwise 3G11nMRW, User Manual

Search results

Summary of Contents for 3G11nMRW

Reviews:

Related manuals for 3G11nMRW

Brands by name

Popular brands