Solwise 3G11nMRW User Manual Download

Page: 41 / 257

Version 1.0.15

4.2.3.9

Wireless Security Setup

The security function is provided to prevent the connection requests from unauthorized

wireless clients. As the

Encryption Type

, select WEP or WPA can protect your data from

eavesdroppers, if you do not need the encryption, select “None ” to skip the following setting.

a. Encrypt Type - WEP

3.5G plus 11n Mobile Server Router supports both 64-bit and 128-bit encryption

using the Wired Equivalent Privacy (WEP) algorithm. Select the type of encryption

you want to use (64 or 128 bit) and conf igure one to four WEP Keys. The “1280bit”

method is more secure than the “64 -bit”.

Key Length:

For 64bits WEP key, 10 hexadecimal digitals leading by

can be

entered. For 128bits WEP key, 26 hexadecimal digits leading by

can be entered.

Key Format:

The keys can be entered in ASCII or Hexadecimal. Select the item

from drop-down list you wish to use.

Key Setting:

A password is requested here.

Note: 128 bits WEP is most secure, but has more encryption/decryption overhead. Note that all wireless device s

must support the same WEP encryption bit size and have the same key.

b. Encrypt Type - WPA, WPA2 & WPA2 Mixed

The WPA and WPA2 encrypt each frame transmitted from the radio using the

pre-shared key (PSK) which entered from this panel or a key got dynamica lly

through 802.1x.

WPA (TKIP) and WPA2 (TKIP):

Allow the access from WPA clients simultaneously

and the encryption keys are given from PSK respectively.

Summary of Contents for 3G11nMRW


































































































































































































































































Search results

Summary of Contents for 3G11nMRW

Reviews:

Related manuals for 3G11nMRW

Brands by name

Popular brands

Solwise 3G11nMRW, User Manual

Search results

Summary of Contents for 3G11nMRW

Reviews:

Related manuals for 3G11nMRW

Brands by name

Popular brands