Solwise 3G11nMRW User Manual Download

Page: 69 / 257

Version 1.0.15

Default Gateway

Input ISP Default Gateway Address. If you don’t know, please check with your ISP.

MTU Size

MTU stands for Maximum Transmission Un it. For Static IP connection, the default MTU

should be provided by computer operating systems (OS). Advanced users can set the MTU

manually for increasing the internet performance. The largest number allowed by Ethernet at

the network layer is 1500 byte

DNS

If ISP provides you DNS information, please select

Attain DNS automatically,

otherwise

select

Set DNS Manually

and input the DNS information into the blank.

3.5G Backup

The default interval between the two connection detection is 3 minutes, and the ra nge is from

1 to 60 minutes. Once Internet connection is disconnected, the system automatically

connects Internet via 3.5G adapter. If 3.5G signal is not available, it starts to search

downward for 3/2.75/2.5G signals until none existed. User needs manual switch through the

GUI setting page to recover the original connection.

Clone MAC Address

Copy the MAC address from the device you had registered to your ISP if your ISP asks for

the specific MAC Address.

Enable IGMP Proxy

The

Internet Group Management P rotocol (IGMP)

is a communication protocol used to

manage the membership of Internet Protocol multicast groups. IGMP is used by IP hosts and

adjacent multicast routers to establish multicast group memberships. You can choose to

enable

IGMP Proxy

to provide service.

Enable Ping Access on WAN

Select

Enable Ping Access on WAN

, will make WAN IP address response to any ping

request from Internet users. It is a common way for hacker to ping public WAN IP address, to

see is there any WAN IP address available.

10. Enable Web Server Access on WAN

This option is to enable Web Server Access function on WAN.

Summary of Contents for 3G11nMRW


































































































































































































































































Search results

Summary of Contents for 3G11nMRW

Reviews:

Related manuals for 3G11nMRW

Brands by name

Popular brands

Solwise 3G11nMRW, User Manual

Search results

Summary of Contents for 3G11nMRW

Reviews:

Related manuals for 3G11nMRW

Brands by name

Popular brands