EN
Before using the product for the first time, please read the
instructions for use below and retain them for later reference.
The original instructions were written in the Hungarian language.
This appliance may only be used by persons with impaired physical,
sensory or mental capabilities, or lacking in experience or knowledge, as
well as children from the age of 8, if they are under supervision or have been
given instruction concerning use of the appliance by a person responsible for their
safety and they have understood the hazards associated with use.
Children should
not be allowed to play with the unit.
Children may only clean or perform user
maintenance on the appliance under supervision.
Featuring a high-powered halogen bulb, this weather-resistant floodlight is perfectly suited
for illuminating buildings or yards. Despite its small size, the floodlight is extremely bright.
Can be mounted on both horizontal and vertical surfaces using the adjustable base. It is
crucial, however, that the bulb is always in a perfectly level position. Otherwise, its lifetime
can be significantly shortened.
The luminary generates a great amount of heat during operation. Do not locate near
flammable materials. Do not touch the unit during operation!
INSTALLATION
Warning! Installation should only be performed by a specialist, in compliance with
the safety and contact protection regulations in force.
1. Warning! Isolate the electrical circuit before mounting and connecting the luminary.
2. The luminary is not suitable for mounting in series.
3. The luminary may only be connected installed cabling!
4. Before commencing installation, please confirm that all parts required are present!
5. The cable can be threaded into the luminary after making a hole in the rubber
stopper. Make sure to enlarge the hole only enough to admit the cable and prevent
any rainwater from seeping in along the cable. The cable should be H05RN-F with a
2
cross section of 3 x 1.0mm !
6. Mount the luminary at the desired location using the included screws and dowels
taking into account the bearing capacity of the wall.
7. Connect the cabling as illustrated below.
8. Insert a line bulb into the luminary as described in section entitled “BULB AND
SCREEN REPLACEMENT”.
9. Replace the glass panel and fasten with a screw. Make sure that the rubber gasket
under the glass panel is clean and fits tightly.
10. Only power on the luminary after this has been done.
CLEANING & MAINTENANCE
In order to ensure optimum functioning, the luminary may require cleaning at least once a
month, depending on the manner of use and degree of contamination.
1.
Power off the luminary prior to cleaning it.
2.
Allow the luminary to cool (for at least 30 minutes).
3.
Use a slightly moistened cloth to clean the luminary's exterior. Do not use any
aggressive cleaners. Avoid getting water inside of and on the electric components of
the luminary.
REPLACING BULBS AND SHIELD
Remove the screw located at the top of the luminary after it has cooled down and power has
been removed. After folding down the front panel, the bulb can be removed from its socket
by pushing it sideways. Avoid touching the replacement bulb with your bare fingers, or clean
it with a soft cloth after insertion, as this may leave oil residue which can shorten its lifetime.
At the same time check the integrity of the shield, and replace with a new one if it is cracked
or broken.
TROUBLESHOOTING
WARNINGS
1.
Confirm that the appliance has not been damaged in transit.
2.
Installation of the product should only be performed by a specialist, in compliance with the
safety regulations in force.
3.
The unit may only be mounted on surfaces of appropriate bearing capacity, at least 1.8
meters above the floor level.
4.
Power off the luminary and wait until it has cooled down before attempting to replace the
bulb (at least 30 minutes).
5.
The luminary may only be used with the shield in place.
6.
Replace shield if broken!
Replace shield if broken
!
Please maintain the required distance from the illuminated
surface (and should be 1,0 m)!
In the event that the power cable should become damaged, it should only be
replaced by the manufacturer, its service facility or similarly qualified
personnel.
Do not discard with communal waste. At the end of its life, dispose of product
at a facility specializing in the collection of electronic waste. If you have any
question or remark in connection with this, contact the seller or local waste
management organization. By doing so, you will protect the environment as
well as the health of others and yourself.
SPECIFICATIONS
Luminary
Meaning of IP44: Protected from the entry of solid objects larger than 1 mm in size.
Protected from splashing water (from all directions).
The luminary works with light bulbs of the following energy rating: C, D, E
operating humidity: <93% RH
operating temperature: -20 - +40 °C
weight: 630 g
outer dimensions: 185 x 155 x 125 mm
maximum projection: 280 sq. cm
Lamp
Energy class of bulb bundled with luminary: C
One
400
W line bulb included
230 VAC / 50 Hz
can be used with max. 1 x
500
W line bulb
bulb: quartz halogen, type R7s,
118
mm x
Ć
10 mm
h
alogen floodlight
FL 500
L – Live: Brown or black conductor
N – Neutral: Blue conductor
– Earth: Green & yellow conductor
Cause
Lamp does not illuminate.
Solution
Check the unit's connections and the power
supply
.
Check if the bulb has burned out
.
1 m
