background image

3

OPERATION

1. Connect the plug of the soldering iron to the socket on the side of the soldering-station. 

2.  Place the soldering iron holder according to the preferred size and angle, then put in the 

soldering iron.

3.  Connect the plug of the soldering station to the mains, then turn on the switch located on its 

front.

4. The surface to be soldered needs to be cleaned thoroughly 

5.  After the heating dip the soldering tip into the soldering tin. The soldering iron is now ready 

for use.

6. Only use as much soldering tin as necessary.

CLEANING

In order for the device to work properly, with a frequency depending on the severity of the 

contamination, but at least once a month the device should require cleaning. Before cleaning 

turn the device off, then cut the power by removing the plug from the socket, and if it is after 

usage leave it to cool down for at least 20 minutes, before starting to clean! Clean the device with 

a soft, dry cloth. Do not use aggressive chemicals! The inside of the device, and the electrical 

parts cannot come into contact with liquids!

TROUBLESHOOTING

Problem

Possible solution of the problem

The soldering iron does not heat up.

Check the mains socket, check the position of 

the toggle switch, check the connection of the 

soldering iron.

The tip of the soldering tin is burnt.

Replace the tip of the soldering iron.

DISPOSAL 

  Waste  equipment  must  be  collected  and  disposed  separately  from  household  waste 

because  it  may  contain  components  hazardous  to  the  environment  or  health.  Used 

or waste equipment may be dropped off free of charge at the point of sale, or at any 

distributor which sells equipment of identical nature and function. Dispose of product at 

a facility specializing in the collection of electronic waste. By doing so, you will protect 

the environment as well as the health of others and yourself. If you have any questions, 

contact the local waste management organization. We shall undertake the tasks pertinent 

to the manufacturer as prescribed in the relevant regulations and shall bear any associated 

costs arising.

Summary of Contents for Home SMA 5051T

















Reviews: