Caution: Risk of electric shock!
Do not attempt to disassemble o
r
modify the unit or its
accessories. In case any part is damaged, immediately power off the unit and seek the
assistance of a specialist.
In the event that the power cable should become damaged, it should only be replaced by the
manufacturer, its service facility or similarly qualified personnel.
FEATURES
ceiling fan with lighting • fan blade diameter: 76 cm • 6 pcs fan blades made of MDF material • 3 stages of fan speed • reversible rotating direction • with cord switches •
E27 socket
Figure
2
.
: 1.
fan blades
•
2.
glass shade of the luminaire
•
3.
on/off switch of lighting
•
4.
switch of fan speed stages
•
5.
rotation direction toggle switch
FAN OPERATION
After powering on the fan, you can operate it with the cord switches. By pulling the cord switch of the lamp, you can
turn on or off the lighting.
The
fan speed can be
adjusted in 3 stages,
which can be operated by the other cord switch. The rotation direction of the fan can be adjusted with the slide switch. ATTENTION! Direction of
rotation can only be changed when the fan moving is stopped. Risk of damage and engine failure!
In the summer
it is advisable to direct the air flow
to the ceiling
to
create a cool, pleasant ventilation. In contrast to it,
in winter,
direct the airflow
downwards
to force the warm air down.
CLEANING, REPLACEMENT OF THE LIGHT SOURCE
I
n order to ensure optimum functioning, the unit may require cleaning at least once a month, depending on the manner of use and degree of
contamination.
1
.
Power off the device by switching off the circuit breaker of its circuit before cleaning and replacing the light source!
2
.
Use a slightly moistened cloth to clean the unit's exterior. Do not use any aggressive cleaners. Avoid getting water inside of and on the electric components of the
appliance!
3
.
If necessary, remove the glass lamp shade and replace the cooled light source. Then put back the lamp shade to its place!
4
.
Install the fan again!
T
ROUBLESHOOTING
TECHNICAL SPECIFICATION
fan power supply
: . . . . . . . . . . . . . . . . . . . . . . . . .
230 V~ / 50 Hz / 50 W
shock protection class
: . . . . . . . . . . . . . . . . . . . . .
I.
ambient temperature
: . . . . . . . . . . . . . . . . . . . . . .
ta +10 - +40 °C
light source power supply
:. . . . . . . . . . . . . . . . . . .
E27 / 1 x max. 60 W / max. 10 cm long
dimensions
: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ø 76 x 28 cm
weight
: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4,1 kg
3
maximum fan - air mass volume
: . . . . . . . . . . . . .
F = 130,36 m /min
fan input power
:. . . . . . . . . . . . . . . . . . . . . . . . . . .
P = 46,1 W
3
service value
: . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SV = 2,83 (m /min)/W
power consumption during standby mode
: . . . . . .
P = 0,0 W
SB
fan acoustic power level
: . . . . . . . . . . . . . . . . . . . .
L = 48,0 dB(A)
WA
maximum air speed
: . . . . . . . . . . . . . . . . . . . . . . .
c = 2,62 m/sec
service value standard: . . . . . . . . . . . . . . . . . . . . . IEC 60879:1986
0
4. Connect the lamp electrically. Ask for the help of a specialist!
0
5. Tilt the motor to its place to horizontal position, then fix it with the 3 screws and spring washers
removed previously. Pay attention to the wires, not to tighten them between the plates.
0
6. Lift the covering metal shade up to the ceiling and fix it with screws. Lead the wires out of the way.
0
7. Screw the metal support brackets to the blades by using 3 screws / washer / spring washer / nut for
each blades. Tighten the screws.
0
8. Fix the metal supports to the motor with the screws and spring washers located there.
0
9. Connect the two cord-switches.
10. Screw in a max. 60 W light source to the E27 socket.
11. Fix the glass lamp shade with 3 screws. Do not tighten them too firmly, since it may lead to the
cracking of the glass lamp shade.
Marking of the terminal block
Power cord
N
neutral wire of 230 V~/50 Hz mains network (blue wire)
L
phase wire of 230 V~/50 Hz mains network (black or brown wire)
grounding wire of 230 V~/50 Hz mains network (green/yellow wire)
Malfunction
Possible solution
The fan does not turn on
.
Check the power supply
!
Turn on/off the switch of rotation direction while the fan is stopped
!
