Mic Placement
Place mic no more than 1/8"
from lips. Placement of mic is
critical for proper operation.
LED Indicators: Charging Depleted Battery
Battery Level Indicator
Number of RED and GREEN
Flashes at Turn ON
No Light
(First 20 Minutes of Charging)
Flashing Red
(While Charging)
Steady Green
(Fully Charged)
20 Minutes
0%
100%
2 Hours
Low Battery (2 hour battery life)
Very Low Battery (15 Minutes battery life)
Red LED Flashing Slow
3 Beeps Every 10 Minutes
Red LED Flashing Fast
6 Beeps Every Minute
BATTERY INDICATORS
H E A D S E T F E A T U R E S
WARNING
If the microphone is positioned incorrectly, you may
experience a reduction or interruption in the audio and
or deterioration in clarity of intercom and radio
communication.
-40
-30
-20
-10
0
10
B
a
tt
e
ry
C
a
p
a
ci
ty
i
n
H
o
u
rs
Degrees
Centigrade
Battery Life vs Temperature
30
25
20
15
10
5
0
20 . . . . . 60
-40
-22
-4
14
32
50
Degrees
Fahrenheit
68 . . . . . 140
75%
>
50-75%
25-50%
25%
<
P A I R I N G
WARNING
To avoid unpairing of existing Headsets, previously paired
Headsets must be ON and connected before pairing a
new Headset.
1.
The unterminated end of the supplied charging cable assembly
and fuse assembly must be wired to the vehicle per the diagram
above.
2.
Observe correct polarity when connecting the charger cable to
12V from the vehicle. Connect the RED wire to +12V and the
BLACK wire to battery chassis ground. This will result in a positive
center terminal of the charger jack as shown in the illustration.
3.
Charge Headset completely before use with vehicle power 12V
supply or supplied wall mount charger
.
4.
For maximum battery shelf life, turn OFF the Headset.
Wall Adapter Charging
Only charge the Headset using the supplied 12VDC regulated wall
adapter. Using unregulated wall adapters will damage the Headset
charging circuit and components and void the warranty.
Vehicle Charging
Note:
Make fuse no further than 18" from the battery.
Note:
Only replace fuse with the same type, 1.5A AGU.
1.5A Fuse
Vehicle Battery
BLACK to Chassis Ground
RED to
CHARGING & INSTALLATIONS
RED
BLACK
Power/Volume
control
Charging Port
Power/Volume
control
Charging Port
Toggle-To-Talk Switch
UP=Radio
Center=Mic On
DOWN=Mic Off
Power/Volume
control
Charging Port
Toggle-To-Talk Switch
UP=Radio
Center=Factory pre-set: Low Squelch
DOWN=Factory pre-set: HighSquelch
PTT Button
APEX
Triton
Headset Adjustments
Behind-the-Head Headset
Over-the-Head Headsets
Over-the-Head Mush Mouth Headsets
Adjustable
headstrap
Adjustable
headband
Adjustable
Boom
Adjustable
Boom
Power/Volume
control
Adjustable
headband
Adjustable
Strap
Power/Volume
control
Headset with
Toggle Switch
Headset with
PTT Button
Headset with
Mush Mouth
WIRELESS BASE
POWER INTERCOM
PAIR
LINKS
1 2 3 4 5
LINKS
1 2 3 4 5
Power On
Toggle Up
Power On
PTT Button
Up=PTT On
C
L
With power ON to Base Station, press the “Pair” button until
Yellow LINK(S) LED’s flash.
To pair Headset to Base Station; hold toggle switch UP, then
turn power ON to Headset or hold PTT button down on the
dome or mush mouth while turning power ON to Headset.
When BOTH Red/Green Headset LED’s are alternating, release
toggle switch or PTT button. Headset will connect to base in
30 seconds.
Up=PTT On
C
When the Headset Green LED remains steadily ON the
headset is successfully paired to the base. If the Headset
Green LED flashes rapidly then repeat the pairing procedure.
A
B
C
Up=PTT On
C
Paired
Not Paired
Power On
PTT Button
Sonetics 600-0175-00 RevB:Layout 1 8/11/11 3:06 PM Page 1
