background image

21 | 

P a g e

 

 

Important Safety Information 

CAUTION! Follow all warnings and instructions marked on the product or 

contained in the owner’s manual. 

 

When using this product, always follow basic safety precautions to reduce the risk 

of fire, electric shock and injury to persons, including the following: 

 

The headset water and dust egress IP rating does not apply when the battery 

door  or Auxiliary input door is open.  DO NOT expose this unit to rain or 

moisture with either door open. 

 

The headset is not certified for explosive environments. Do not use the headset 

to report a gas leak in the vicinity of the leak. 

 

There are no user serviceable parts inside the headset. Disassembly will void 

the warranty and will degrade the water sealing and hearing protection. 

 

Use only the power adapters, power cords and batteries indicated in the 

manual. If more than one type of power adapter is included in the product, the 

manual specifies which adapter should be used for each component. Be sure to 

use the proper adapter for each product component. 

 

Do not place the power cord where it creates a trip hazard or where it could 

become chafed and create a fire or electrical hazard. 

 

Do not subject the unit to high temperatures or leave it in direct sunlight for an 

extended period of time. 

 

Retention of dangerous objects:  The Headset may hold small objects in the 

area of the earpiece. Before use, check that the earpiece area is free of staples, 

pins, clips or any other small metallic objects or foreign matter. 

SAVE THESE INSTRUCTIONS

 

General Warning for Sensitive Electronic Devices  

This  equipment and any radio-based can electronic potentially cause 

electromagnetic based interference with other equipment and can be interfered 

with other equipment. This also applies with DECT based Equipment. Due to the 

very low transmission power associated with DECT the chance for interference is 

small. However some specific precautions must be taken into account for sensitive 

electronic equipment e.g. sensitive laboratory equipment, medical instruments or 

medical implants to avoid incidental influence of equipment operated in straight 

nearness to sensitive electronic equipment. You are therefore advised not to place 

the DECT equipment or its antenna in close proximity to sensitive equipment by 

maintaining a 20cm minimum distance between the sensitive equipment even in 

standby mode. Please also consider referencing the documentation provided by us 

and the manufacturer of sensitive electronic items guiding its proper usage.

 

General Communication Privacy Notice 

Although this equipment may contain specific protocols that enhance security and 

privacy of communication, privacy of communication may not be ensured when 

using this equipment.

 

 

Industry Canada (I.C.) Notice 

This section applies to radio frequency equipment bearing an I.C. Equipment ID 

Number (UPN). 

This device if labeled with an IC UPN, complies with Industry Canada license-exempt 

RSS standard(s).  

Operation is subject to the following two conditions:  

(1) this device may not cause interference, and  

(2) this device must accept any interference, including interference that may cause 

undesired operation of the device. 
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux 

appareils radio exempts de licence. Son fonctionnement est sujet aux deux 

conditions suivantes:  

(1) le dispositif ne doit pas produire de brouillage préjudiciable, et  

(2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage 

susceptible de provoquer un fonctionnement indésirable. 
Canada SAR Information: 

This device contains a radio transmitter. This device has been shown to be capable 

of compliance for localized specific absorption rate for uncontrolled environmental 

/ general public exposure limits specified in RSS-102, ANSI/IEEC95.1-2002 and have 

been tested in accordance with the measurement procedures specified in IEE 1528-

2003. 
Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites 

d'exposition aux rayonnements IC établies pour un environnement non contrôlé. 

Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance 

entre la source de rayonnement et votre corps. 
Any base station or approved base station antenna meant to be used in conjunction 

with this equipment must not be used in close proximity to the body. Keep a 

minimum distance of greater than 20 CM to the human body. This device and 

antenna must not be co-located in conjunction with any other equipment antenna 

or transmitter. 

This class A digital apparatus complies with Canada ICES-003. CET appareil 

numérique de la classe A est conforme à la norme NMB-003 et CNR 210 d’Industrie 

Canada. 

Summary of Contents for APX37x




























Reviews: