background image

SonicWALL Installation Guide Page 75

Receive (RX)

 

The 

RX

 light is lit when data is received over the network connection. 

Link

 

The Link LED indicates that the interface is connected to a valid link partner and is
receiving link pulses. 

The 1000Base-T network interface has the following LEDs:

Link

 

The 

Link

 light is green when a network

 

connection is made to another Ethernet device

(usually a hub) on the port.

Activity

 

The 

Activity

 LED blinks, indicating 

Activity

, when the SonicWALL transmits or

receives a frame.

Network Speed

 

The 

Network Speed

  light  remains  off  if  there  is  no  connection  or  if  a  10Mbps

connection is made. If a 100 Mbps connection is made, the LED is green. If a 1000
Mbps connection is obtained, the LED is yellow.

Reset Switch 

Resets the SonicWALL GX 250 or the SonicWALL GX 650 to its factory clean state. This may be
required if you forget the administrator password, or the SonicWALL firmware has become
corrupt. 

SonicWALL GX 250 and GX 650 Rear Panel

The SonicWALL GX 250 back panel is shown below, followed by a description of each item. 

The

SonicWALL GX 650 back panel is identical to the SonicWALL GX 250.

SonicWALL GX 250 and SonicWALL GX 650 Back Panel Description 

Power Inputs

 

Power Input

Power

Switches

Cooling Vent

Alarm Reset Button

Summary of Contents for GX 250

























































































Reviews: