background image

Quick Start Guide ONLY for Encore/ST G4 Duet 1.8 GHz 

Remember to register your product online at http://registration.sonnettech.com to be informed of future upgrades and product releases.
Software updates and links are available from the Sonnet web site at www.sonnettech.com. • Online support form available at http://supportform.sonnettech.com.
Sonnet Technologies Customer Service hours are Mon.-Fri., 7 a.m.–4 p.m. Pacific Time • Customer Service Phone: 1-949-472-2772 • E-mail: support@sonnettech.com
Sonnet Technologies, Inc., Irvine, California USA • Tel: 1-949-587-3500 Fax: 1-949-457-6350 

©2008  Sonnet Technologies,  Inc.  All  rights  reserved.  Sonnet,  the  Sonnet  logotype,  Simply  Fast,  the  Simply  Fast  logotype  and  Encore  are  trademarks  of  Sonnet Technologies,  Inc.  Macintosh  and  Mac  are  trademarks 
of Apple  Inc.,  registered  in  the  United  States  and  other  countries.  Other  product  names  are  trademarks  of  their  respective  owners.  Product  specifications  subject  to  change  without  notice.  Printed  in  the  USA. 
QS-SG4D-1800-E-B-010708

Quick Start Guide ONLY for Encore/ST G4 Duet 1.8 GHz 

%.#/2%

»

34'

$5%4'(Z

$UAL0ROCESSOR5PGRADE#ARDFOR0OWER-AC

š

'#OMPUTERS

 

Power Mac and Operating System Compatibility

This Encore/ST G4 Duet processor upgrade card is compatible only with Power 
Mac G4 AGP Graphics, Gigabit Ethernet, Digital Audio, QuickSilver 2001, and 

QuickSilver 2002 models. 

Installation of this product into a Power Mac G4 Cube is 

not supported

If you are unsure which Power Mac model you have, refer 

to Apple’s online support article that describes the differences at  

http://docs.info.apple.com/article.html?artnum=58418

. This article 

lists model numbers, and describes the physical differences of the various 

Power Mac G4 models. 

 

At this printing, this Encore/ST G4 Duet processor upgrade is  

compatible with Mac OS

®

 9.2 and Mac OS X Version 10.3.5 and 

later. For up-to-date Mac OS compatibility information, check our 

Web site. 

Encore/ST G4 Duet processor upgrades do not cause sleep issues in computers 
that support sleep with the original processor installed. If a computer experi-
ences sleep issues with the original processor installed, installing this upgrade is 
unlikely to change that condition. In the very rare instance where a computer 
begins to have sleep issues after a Duet upgrade is installed, the problem is iso-
lated to that specific card and can be resolved by replacing it. 

You Should Have

The following items should be included in your product package:
• Encore/ST G4 Duet processor upgrade card*
• Sonnet Installer CD

The following items are required for installation:

• Medium Phillips screwdriver 
• Flat blade screwdriver (only for QuickSilver installation)
• Needle-nose pliers

* Your card may differ from what is pictured.

 

 Support Notes:

 Please familiarize yourself with 

the following instructions before beginning the 

installation. If you feel you are unable to install the com-
puter hardware, please contact a qualified computer 
technician. Sonnet strongly recommends that a qualified 
technician perform this installation.

Before proceeding with the installation, we recommend 
that you backup important information on your hard 
drive prior to installing new hardware or software. 

 

 WARNING:

 

Some Power Mac G4 (AGP Graphics) models are 

incompatible with dual processor cards

. If you purchased this 

upgrade for a Power Mac G4 (AGP Graphics) computer, be sure to 
read the included warning sheet for information on how to determine 
whether your system is compatible before you install this product. 

In order for this Encore/ST G4 Duet to operate in your system, it 
must have the latest Power Mac G4 firmware installed. If you use 
Mac OS X, you must ensure that it is Version 10.3.5 or later; earlier 
versions are NOT compatible.

 If your system does not meet these cri-

teria, you must upgrade to the correct OS version(s) and update your 
system’s firmware before installing this upgrade. Otherwise, your sys-
tem will not operate with the Duet installed. Instructions follow.

Multiple Upgrade Recommendation

If you intend to perform multiple hardware upgrades to 
your Power Mac, we recommend that you complete the 
installation of the Encore/ST G4 Duet first, and then 
install the remaining upgrades; 

complete each upgrade 

and test it before proceeding to the next

Summary of Contents for Encore ST G4
















Reviews: