Sonnet Fusion R400 User Manual Download

Page: 3 / 12

1 Fusion R400 RAID USB 3.0 Features

2 Drive Installation and Enclosure Setup 2

Install Drives
Connect the Fusion R400 RAID USB 3.0 to Computer and Power Outlet

3 Drive Mode Descriptions 3

    RAID 0: Striping, No Redundancy
    RAID 10: Striping, Mirror Spans Two Drives
    Span: Concatenation, Volume Spans Four Drives
    RAID 5: Striping, Parity Distributed Among Drives
    JBOD: Just a Bunch of Disks

4 Drive Mode Configuration Instructions 5

General Information
Select Drive Mode

5 Drive Formatting Instructions 6

    OS X Users’ Instructions
    Windows 8/7/Vista and Server 2012/2008 Users’ Instructions
    Linux Users’ Information

6 Status LED Indications

    System Powered, No Data Reads or Writes
    Drive Activity
    Drive Not Recognized
    RAID 5 or RAID 10 Rebuild
    Bad Drive Detected

7 Specifications, Warnings, and Additional Information

   Specifications
    Safety Precautions
   Warnings
    FCC Compliance
    Contacting Customer Serrvice
    Visit Our Website

Contents

Summary of Contents for Fusion R400













Search results

Summary of Contents for Fusion R400

Reviews:

Related manuals for Fusion R400

Brands by name

Popular brands

Sonnet Fusion R400, User Manual

Search results

Summary of Contents for Fusion R400

Reviews:

Related manuals for Fusion R400

Brands by name

Popular brands