3-14
BKS-R3219A/R1617A I&SSM
.....
Procedure of setting SELECT SOURCE NAME
Sets the source terminals that can be selected for a specific
destination terminal. The terminals are not enabled and
disabled individually. Instead, a range of terminals is set as
enabled.
1.
Press
[Ctrl]
_
[F]
to switch to the SELECT SOURCE
NAME screen.
2.
Select an item to set using the cursor key.
3.
Pressing
[Enter]
establishes the source name input
mode.
4.
Enter the “Type
+
No.” name or description name.
1) When [J : NAME STYLE (Type
+
Num)] is
selected in the primary station menu, input the
type name (between 0 and F) and the number for
the source and destination name.
2) Each time
[Ctrl]
_
[N]
is pressed when [J :
NAME STYLE (DESCRIP. NAME)] is selected
in the primary station menu, the following input
mode will be switched alternately.
When “Ctrl
_
N : Type
+
Num” is displayed on the
screen, it means that the name mode will be changed to
“Type
+
Number” by pressing
[Ctrl]
_
[N]
.
Description name input mode :
Input Description name from the first to seventh
characters using the alphabet and numerical keys.
“Type
+
Number” name input mode:
Input in the same way as 1).
5.
Press
[Enter]
to confirm the input contents.
Example of setting
Block
Source
Destination
(Used area)
(Input range)
(Output range)
TOP
END
TOP
END
1
1
64
1
64
2
101
164
1
64
3
101
164
101
164
When the ranges of input and output selections are limited
as shown in the above table, the setting display and the
virtual matrix are configured as shown below.
SONY ROUTING SYSTEM SETUP MENU BKS-R3219A V2.23 STATION NUMBER 4
SELECT SOURCE NAME
SRC TOP -SRC END =DST TOP -DST END
001 IN001 -IN064 =OUT001 -OUT064
002 IN101 -IN164 =OUT001 -OUT064
003 IN101 -IN164 =OUT101 -OUT164
004 ....... -....... =....... -.......
005 ....... -....... =....... -.......
006 ....... -....... =....... -.......
007 ....... -....... =....... -.......
008 ....... -....... =....... -.......
0=IN 1=OUT 2=SONY 3=VTR 4=SUP 5=CB 6=AIR 7=ME
8=PGM 9=CL A=SL B=L C=RET D=MIX E=JEEP F=OSC
G=L/A H=REM I=CAM J=STDO K=AUX L=COV M=BS N=CS
O=SAT P=CG Q=WETH R=TEST S=HD T=D1- U=D2- V=SEG
Ctrl-E:MENU Ctrl-D:RETURN Ctrl-N:Type + Num Ctrl-F:SELECT DESTINATION
1
64
64
101
101
164
1024
164
1024
(Input)
(Output)
: Unset range
Block 1
Block 2
Block 3
Virtual matrix
: Set range
m
1.
When selecting the destinations that have no limit of
range, the selectable range of sources is from 1 to 1024.
When the selections are the same as the example of the setting
screen, all of the sources 1 to 1024 can be selected for OUT065.
2.
Sources included in the range of the selected destina-
tion will be all set enables. When selected by the
example setup screen, OUT001 will enable multiple
ranges of IN001 - IN064 and IN101 - IN164.
To return to the menu screen of the secondary station
Press
[Ctrl]
_
[E]
.
To return to the menu screen of the primary station
Press
[Ctrl]
_
[D]
.
Example of Selectable Source Range Setting Screen
