1-5
CCU-TX7 (E)/V1
9
CCU-TX7/TX7P switches and knobs
1
TALLY lamp
The lamp lights red when a red tally signal is received
and green when a green tally signal is received.
It also lights red when the CALL button is pressed on
the CA-TX7/TX7P Camera Adaptor or RCP-TX7
Remote Control Panel connected to this unit.
The camera number plate (provided) can be attached to
this lamp.
2
CABLE ALARM indicator
SHORT: this indicator lights when an overcurrent
occurs in the triaxial cable connected to the
CAMERA connector on the rear panel.
OPEN: this indicator lights when there is no triaxial
cable connected to the CAMERA connector on
the rear panel or when the current flowing in the
connected triaxial cable is excessively small.
3
CALL button
When you press this button, it lights along with the red
TALLY lamps and CALL buttons on the video
camera, camera adaptor, and remote control panel
connected to this unit. This function can be used to call
the video camera or remote control panel operator.
You can then talk with the operator via the intercom.
This button also lights when the CALL button is
pressed on the camera adaptor or remote control panel.
4
INTERCOM audio input/output and setting
section
INTERCOM connector (XLR 5-pin): Use this to
connect a headset.
INTERCOM (intercom level) knob: Use this to
adjust the intercom sound volume.
PGM (program audio level) knob: Use this to
adjust the sound volume when monitoring
program audio via a headset.
MIC switch: Use this switch to turn the headset’s
microphone ON or OFF.
LINE switch: Use this switch to select the channel
for intercom signals that are input and output via
the INTERCOM connector.
• CH1: Connects to channel 1
• CH2: Connects to channel 2
• PRIV: Does not connect to channel 1 or
channel 2. Instead, the intercom operates only
between this unit and the connected video
camera.
5
CAMERA POWER switch and indicator
When the POWER switch is on, use this switch to
switch the power on and off to the video camera and
camera adaptor connected to this unit. The indicator
lights when this switch is turned on powering the
camera adaptor.
6
POWER switch and indicator
This switches the power to this unit on or off. The
indicator lights when the power is on.
A
A
1
1
TALLY
POWER
CABLE ALARM
INTERCOM
CAMERA
POWER
SHORT
CALL
ON
MIC
ON
OFF
INTERCOM
LINE
CH1
CH2
PGM
PRIV
OFF
OPEN
PUSH
1
TALLY lamp
2
CABLE ALARM indicator
3
CALL button
4
INTERCOM audio input/
output and setting section
5
CAMERA POWER switch
and indicator
6
POWER switch and
indicator
INTERCOM
MIC
ON
OFF
INTERCOM
LINE
CH1
CH2
PGM
PRIV
PUSH
MIC switch
LINE switch
PGM knob
INTERCOM knob
INTERCOM connector
8
Location and Function of Par t s
Various switches, adjustment knobs, and connectors
are located on the front panel, rear panel, and also on
the edges of internal boards.
Location and Function of Parts
Front P anel
From the front panel, you can operate the CCU-TX7/
TX7P’s switches and knobs as well as the camera
operation unit’s switches and knobs (when the optional
COU-TX7 Camera Operation Unit has been installed).
For description of how to install the camera operation unit,
see “Installing the Camera Operation Unit” (page 7).
TALLY
SHUTTER
KNEE
IRIS
WHITE/BLACK BALANCE
OUTPUT
M.GAMMA
GAIN
TLCS
DETAIL
OPERATE
POWER
CABLE ALARM
INTERCOM
CAMERA
POWER
SKIN
DETAIL
MASTER
BLACK
SHORT
CALL
ON
MIC
ON
OFF
INTERCOM
LINE
CH1
CH2
PGM
PRIV
OFF
OPEN
LOCK
PART
FULL
HIGH
MID
LOW
CAM
BARS
ON
Hz
OFF
ON
C.SCAN
AUTO
MANUAL
AUTO
PRESET
WHITE
BLACK
BLACK
WHITE
AUTO
ATW
MANUAL
AUTO
MANUAL
OFF
PRE
PUSH
CCU-TX7/TX7P switches and knobs
(see page 9)
Camera operation unit switches and knobs
(see page 10)
