background image

3

LASER  DIODE  AND  FOCUS  SEARCH  OPERATION
CHECK

Carry out the “S curve check” in “CD section adjustment” and
check that the S curve waveforms is output three times.

Notes on chip component replacement

• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-

aged by heat.

Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270 ˚C dur-

ing repairing.

• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering

or unsoldering.

SECTION  1

SERVICING  NOTES

CAUTION

Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous ra-
diation exposure.

This appliance is classified as a CLASS 1 LASER product.
The CLASS 1 LASER PRODUCT MARKING is located on
the rear exterior.

The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.

NOTES  ON  LASER  DIODE  EMISSION  CHECK

The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emis-
sion, observe from more than 30 cm away from the objective lens.

NOTES  ON  HANDLING  THE  OPTICAL  PICK-UP
BLOCK  OR  BASE  UNIT

HOW  TO  OPEN  THE  DISC  TABLE  WHEN  POWER
SWITCH  TURNS  OFF

Insert a tapering driver into the aperture of the unit bottom, and
turn it in the direction of the arrow (to OUT direction).

table

tapering driver

*

To close the disc table, turn the tapering 
driver in the reverse direction (to IN direction).

Part No.

Model

Part No.

CDP-CE245: US model

4-224-877-0

s

CDP-CE245: Canadian model

4-224-877-1

s

CDP-CE245: Australian model

4-224-877-2

s

CDP-CE345: US model

4-224-878-0

s

CDP-CE345: Canadian model

4-224-878-1

s

CDP-CE345: AEP model

4-224-878-2

s

CDP-CE345: UK model

4-224-878-3

s

CDP-CE345: Australian model

4-224-878-4

s

CDP-CE345: E model

4-224-878-5

s

CDP-CE345: Singapore model

4-224-878-6

s

CDP-CE345: Saudi Arabia model

4-224-878-7

s

MODEL  IDENTIFICATION
– BACK PANEL –

Summary of Contents for CDP-CE245 - Compact Disc Player













































Reviews: