9
31
Storing the TV channel
names
Follow the steps in “Storing the station
names” (page 20).
Displaying the TV or radio station
names
Press
(LIST)
during TV or radio reception.
Example: When receiving the FM1 band
1
Preset number
2
Stored station names
3
Frequencies
*
*
If the name of a station is not stored, the
frequency of that station will be displayed
instead.
Notes
• It may take some time before all indications
appear in the display.
• The TV channel does not appear during list
display.
• The contents of the preset memory cannot be
listed when the unit is in simultaneous play
mode (page 32).
Turning off the display
During radio reception, press
(LIST)
again.
During TV reception, the list display on the
TV monitor will automatically turn off after
a few seconds.
Displaying the
information stored on
discs
Press
(LIST)
during CD/MD playback.
Example: When CD unit 1 is selected.
1
Disc numbers
2
Titles stored as custom files
3
No disc is loaded
*
1
4
No stored titles
*
2
5
TOC information has not been identified yet
*
3
*
1
A blank space is displayed next to a disc
number represents empty slots in the disc
magazine.
*
2
If a title is not registered in the custom file,
“
******
” is displayed.
*
3
If the disc information has not been read yet by
the unit, “?” is displayed.
Notes
• It may take some time until all indications appear
in the display.
• The TV channel does not appear during list
display.
• The contents of the preset memory cannot be
listed when the unit is in the simultaneous play
mode.
Turning off the display
Press
(LIST)
again.
FM
1
2
3
4
5
6
W
W
W
C
B
K
1
1
B
T
0
0
S
U
2
S
WR K I S
1
S
L
1 . 9
. 7
CD 1
1
2
3
4
5
6
7
9
1 0
8
S
M
B
L
C
C
O
A
I
H
H
Z
C
S
O
U
A
H
Z
P
B
R
T
I
E
T
N
R T
*
?
?
* * * **
* * * * **
32
Watching the TV or video
while listening to a CD or
MD
—
Simultaneous Play
The simultaneous play function does not work
while you are listening to the radio.
1
Press
(MENU)
, then press either side of
(DISC/PRST)
repeatedly until “Simul Sel”
appears.
2
Press
(ENTER)
.
3
Press (–) side of
(SEEK/AMS)
.
4
Press
(SOURCE)
repeatedly to select CD
or MD.
5
Press (+) side of
(SEEK/AMS)
.
6
Press
(SOURCE)
repeatedly to select a TV
or video.
7
Press
(ENTER)
.
Simultaneous Play starts.
If you are already watching the TV or video
and want to listen to a CD or MD as well,
follow the same steps above.
Returning to normal mode
To cancel the CD or MD, follow the steps
above and select “– – –” in step 4.
To cancel the TV or video, follow the
steps above and select “– – –” in step 6.
Note
If you press
Z
(EJECT) on a CD/MD unit while the
unit is in simultaneous play mode, Simultaneous
Play is canceled.
33
Additional
Information
Maintenance
Fuse replacement
When replacing the fuse, be sure to use one
matching the amperage rating stated on the
original fuse. If the fuse blows, check the
power connection and replace the fuse. If the
fuse blows again after replacement, there may
be an internal malfunction. In such a case,
consult your nearest Sony dealer.
Warning
Never use a fuse with an amperage rating
exceeding the one supplied with the unit as
this could damage the unit.
Fuse (10 A)
Cleaning the connectors
The unit may not function properly if the
connectors between the unit and the front
panel are not clean. In order to prevent this,
open the front panel by pressing
(OPEN)
, then
detach it and clean the connectors with a
cotton swab dipped in alcohol. Do not apply
too much force. Otherwise, the connectors may
be damaged.
Main unit
Back of the front panel
Notes
• For safety, turn off the engine before cleaning
the connectors, and remove the key from the
ignition switch.
• Never touch the connectors directly with your
fingers or with any metal device.
34
Dismounting the unit
1
Press the clip inside the front cover with
a thin screwdriver, and gently pry the
front cover free.
2
Repeat step 1 on the left side.
The front cover is removed.
3
Use a thin screwdriver to push in the clip
on the left side of the unit, then pull out
the left side of the unit until the catch
clears the mounting.
4
Repeat step 3 on the right side.
5
Slide the unit out of the mounting.