CFD-CD777SMK2
5
8
GB
Playing a tape
For hookup instructions, see pages 19 — 20.
1
Set FUNCTION to TAPE¥CD/
RADIO OFF.
2
Press
xZ
to open tape compartment
and insert a recorded tape. Use TYPE
I (normal) tape only. Close the
compartment.
3
Press PLAY
N
.
The player starts playing.
With the side you want
to play facing you
3
2
1
3
2
Basic Operations
9
GB
Use these buttons for additional operations
To
Do this
adjust the volume
Turn VOLUME.
stop playback
Press
xZ
.
fast-forward or rewind the tape
Press
m
or
M
.
pause playback
Press
X
.
Press the button again to
resume play after pause.
play the opposite side of
Press down DIRECTION
the tape (deck A only)
once.
DIRECTION
h
H
(reverse/
forward) indicators show the
tape direction of deck A.
eject the cassette
Press
xZ
.
To select the direction of the tape (deck A
only)
To play
Set DIR MODE to
both sides of the tape
repeatedly
both sides of the tape
from the front side to
reverse side only*
* If play begins from the reverse side, the tape stops at the end of
that side.
DIRECTION
h
H
DIR MODE
Level meter
VOLUME
xZ
X
m
,
M
m
,
M
X
xZ
Note
During playback, do not
press
M
,
m
or
N
on
the other deck as this causes
excessive wow and flutter.
Tips
¥ During operation, the level
meter shows the frequency
level of the sound.
Adjusting the volume will
not affect the level meter.
¥ To play tapes in both decks
successively, press
N
on
deck B and then press
PLAY and
X
on deck A as
the same time. When the
tape ends on deck B, the
playback starts
automatically on deck A.
10
GB
Recording on a tape
1
Press
xZ
to open the tape
compartment on deck B and insert a
blank tape. Use TYPE I (normal)
tape only. Close the compartment.
2
Select the program source you want
to record.
To record from the CD player, set
FUNCTION to CD and insert a CD
.
To record from the radio, set
FUNCTION to RADIO, and tune in
the station you want using BAND
and TUNING.
To record from the built-in
microphone (MIC), set FUNCTION
to TAPE¥CD/RADIO OFF.
With the side you want to
record on facing you
Display
3
1
2
MIC
Basic Operations
11
GB
3
Start recording.
Press
z
on deck B (
N
is depressed
automatically).
Use these buttons for additional operations
Notes
¥ During recording, do not
press
M
,
m
or PLAY
on deck A as this causes
excessive wow and flutter.
¥ While recording from the
built-in microphone (MIC),
no sound comes from the
speakers or the headphones.
¥ When you connect the
microphone to the MIX
MIC jack, you cannot
record from the built-in
microphone.
Tips
¥ Adjusting the volume or
selecting the audio
emphasis will
not
affect the recording
level.
¥ If the MW program makes
a whistling sound after
you’ve pressed
z
in step 3,
set the ISS¥FM MODE
(Interference Suppress
Switch) at the rear to the
position that most decreases
the noise.
¥ For the best results, use the
AC power as a power
source.
¥ To erase a recording,
proceed as follows:
1 Insert the tape into deck
B.
2 Disconnect the audio
source if connected to the
TV/LINE IN jack at the
rear.
3 Set FUNCTION to TV/
LINE IN.
4 Press
z
on deck B.
xZ
X
n
To
Press
stop recording
xZ
on deck B
pause recording
X
on deck B
Press the button again to resume
recording.
Deck B
xZ
X
Summary of Contents for CFD-CD777S MK2
Page 64: ...64 CFD CD777SMK2 MEMO ...
