EN
21
A stereo FM program cannot be
received in stereo.
m
When "MONO" appears in the
display, press STEREO/MONO on
the remote so that "MONO"
disappears.
m
Adjust the antenna.
Timer
The timer does not function.
m
Set the clock correctly.
m
AC power has been cut off. While
the timer functions, press the
POWER switch to turn off the
system.
m
Make sure “DAILY” or “REC”
appears in the display.
Remote
The remote does not function.
m
The batteries have run down.
Replace both batteries.
m
There is an obstacle between the
remote and the system. Remove
the obstacle.
Maintenance
To clean the tape heads and tape
path
Contaminated tape heads cause poor
recording or sound drop-out in playback.
We recommend cleaning after every 10
hours of operation.
Open the tape compartment and wipe the
heads, the pinch rollers and the capstans
with a cleaning swab slightly moistened
with cleaning fluid or alcohol. Wipe the
parts shown below:
Insert a tape when the areas cleaned are
completely dry.
To demagnetize the tape heads
After 20 to 30 hours of use, enough residual
magnetism will have built up on the heads
to begin to cause loss of high frequencies
and hiss. At this time, demagnetize the
heads and all metal parts in the tape path
with a commercially available tape head
demagnetizer. Refer to the instructions of
the demagnetizer.
To clean the cabinet
Use a soft cloth slightly moistened with
mild detergent solution.
To clean the CD
When a CD is dirty, clean it with a cleaning
cloth. Wipe the CD from the center out.
Notes on CD
• Do not use solvents such as benzene,
thinner, commercially available cleaners,
or anti-static spray intended for vinyl LPs.
• If there is a scratch, dirt or fingerprints on
the CD, it may cause a tracking error.
Specifications
Tuner CD player (HCD-T1)
Tuner section
Tuning range
FM: 87.5 – 108 MHz
AM: 531 – 1,710 kHz
(at 9 kHz interval)
530 – 1,710 kHz
(at 10 kHz interval)
Intermediate frequency
FM: 10.7 MHz
AM: 450 kHz
Antenna terminals
FM: 75 ohm unbalanced
AM: External antenna terminal
Timer
Quarts lock system
Timer setting
One-minute step
Sleep timer
10-minute step, max. 90
minutes
CD player section
System
Compact disc digital audio
system
Laser
Semiconductor laser
(
λ
= 780 nm)
Laser output power
Less than 44.6
µ
W*
* This output is the value measured at a
distance of 200 mm from the objective lens
surface on the optical pick-up block with 7
mm aperture.
Frequency response
2 Hz – 20 kHz
±
0.5 dB
Signal to noise ratio
More than 90 dB
Harmonic distortion
Less than 0.03%
Preamplifier section
Frequency response
15 Hz – 50 kHz
+0
dB
–3
Inputs
PC/MD IN:
Stereo phone jack, sensitivity
450 mV, impedance 47 kilohms
For Your Information
The CD will not play.
m
The CD is dirty.
m
The CD is inserted label side
down.
m
The player is in pause mode.
m
Moisture condensation has built-
up. Leave the system turned on
for about an hour until the
moisture evaporates.
Play does not start from the first
track.
m
The CD player is in program or
shuffle mode. Press TUNING/
PLAY MODE repeatedly until the
play mode indication disappears.
Cassette deck
The tape does not record.
m
No tape in the tape compartment.
m
The tab has been removed from
the cassette.
m
The tape has reeled to the end.
The tape does not record nor does it
play back, or there is a decrease in
sound level.
m
The heads are dirty. Clean them.
m
Magnetic deposits have built-up
on the record/playback head*.
There is excessive wow or flutter, or
the sound drops out.
m
The capstans or pinch rollers are
contaminated*.
The tape does not erase completely.
m
Magnetic deposits have built-up
on the record/playback head*.
Noise increases or the high
frequencies are erased.
m
Magnetic deposits have built-up
on the record/playback head*.
CD Synchronized recording does not
start.
m
When you set the tape direction to
a
, recording does not start if the
tab of either side is removed from
the cassette.
*See “Maintenance”.
Tuner
”TUNED” flashes in the display.
m
Adjust the antenna.
”STEREO” flashes in the display.
m
Adjust the antenna.
Severe hum or noise.
m
Adjust the antenna.
m
The signal strength is too weak.
Connect the external antenna.
m
Connect the earth wire.
Capstan
Pinch roller
Playback head
Erase head
Cleaning swab
continue to next page
➔
