DSC-RX10_L2
2-6
2-1-3. FRONT CABINET SECTION 1
ns : not supplied
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
101
A-1989-834-A CD-847 FLEXIBLE BOARD, COMPLETE (SERVICE)
(Note2, 3, 4)
102
4-470-413-01 RUBBER,
SEAL
103
4-478-904-01 SCREW,
TRIPOD
104
X-2588-287-1 STRAP EYELET ASSY (L)
*
105
4-478-903-01 FRAME, MAIN
106
A-1992-176-A HOLDER ASSY, SY (SERVICE)
107
Selection Parts SPACER PLATE
108
4-478-915-01
SHEET METAL, JK ELECTROSTATIC
109
4-528-669-01
SHEET (SY HOLDER)
#1
2-635-562-11 SCREW(M1.7)
#12
3-080-204-21 SCREW,
TAPPING,
P2
#155 3-080-204-31 SCREW,
TAPPING,
P2
#305
3-703-816-19
SCREW (M1.4X4.0), SPECIAL HEAD
1. Remove in numerical order (
1
to
4
) in the left figure.
DISASSEMBLY
Lens Block Section
(Note 1, 2)
Front Cabinet Section 2
2
1
4
3
(Note 5)
(Claw)
101
102
103
106
105
108
109
104
107
107
#12
#305
#12
#12
#155
(including CP001
(CMOS imager))
(Note 2, 3, 4)
#155
#1
ns
ns
ns
2
#12 X 4
4
#155 X 4
Back View
#12
#12
#12
Back View
#155
#155
#155
Screw
#1: M1.7 X 2.5
(Black)
2-635-562-11
2.5
1.7
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
1.7
5.0
1.7
6.0
#155:
M1.7 X 6.0 (Tapping)
(
Black
)
3-080-204-31
4.0
#305: M1.4 X 4.0
(Black)
3-703-816-19
1.4
SELECTION PARTS
Ref. No.107
These parts are provided for shift and tilt adjustment. Change the thickness
(t) according to result of adjustment
4-410-539-01
SPACER PLATE (A) (t=0.10)
4-410-539-21
SPACER PLATE (A) (t=0.12)
4-410-539-41
SPACER PLATE (A) (t=0.14)
4-410-539-61
SPACER PLATE (A) (t=0.16)
4-410-539-81
SPACER PLATE (A) (t=0.18)
4-410-540-01
SPACER PLATE (B) (t=0.20)
4-410-540-21
SPACER PLATE (B) (t=0.22)
4-410-540-41
SPACER PLATE (B) (t=0.24)
Note 2:
When this part is removed, adjustment is required.
For the adjustment method, refer to “Adjustment items after
replacing parts” in the Note tab of the Adjust manual.
Note 2:
この部品を取り外したときは調整が必要です。
調整方法については
Adjust manual
の
Note
タブにある
Adjust-
ment items after replacing parts
を参照してください。
Refer to “1-3. NOTES ON REMOVING/INSTALLING THE
IMAGER BOARD (CD-847 FLEXIBLE BOARD)”.
Note 4:
Be sure to read “Precautions for Replacement of Imager” on
page 6-1 of Level 3 when changing the imager.
Note 4:
イメージャの交換時は
Level 3
の
6-1
ページ、“イメージャ交換時
の注意”を必ずお読みください。
Refer to “Assembly-4: Notes on assembling the SY Holder
Assy” when assembling.
Assembly-4: Notes on assembling the SY Holder Assy
Note
Note 1 :
Hold the Lens Block at the
center of both sides.
Do not hold the following part.
Hold here.
NOTES ON HOLDING THE LENS BLOCK
Very weak
Very weak
Very weak
Very weak
4-410-540-61
SPACER PLATE (B) (t=0.26)
4-410-540-81
SPACER PLATE (B) (t=0.28)
4-437-388-01
SPACER PLATE C (t=0.30)
4-437-388-21
SPACER PLATE C (t=0.32)
4-437-388-41
SPACER PLATE C (t=0.34)
4-437-388-61
SPACER PLATE C (t=0.36)
4-437-388-81
SPACER PLATE C (t=0.38)
4-472-511-01
SPACER PLATE D (t=0.40)
4-472-511-21
SPACER PLATE D (t=0.42)
4-472-511-41
SPACER PLATE D (t=0.44)
4-472-511-61
SPACER PLATE D (t=0.46)
4-472-511-81
SPACER PLATE D (t=0.48)
4-472-512-01
SPACER PLATE E (t=0.50)
