2-6
HDR-CX530E/CX535/CX610E/PJ530E/PJ540/PJ540E/PJ610E_L2
(Bosses)
(Bosses)
(Bosses)
(Boss)
(Boss)
(Boss)
(Boss)
(Claw)
151
#278
(Note 1)
#278
(Note 1)
#278
(Note 1)
#278
(Note 1)
#288
(Note 1)
#289
(Note 1)
#289
(Note 1)
#289
(Note 1)
#289
(Note 1)
#289
(Note 1)
A
#290
#290
#290
#278
(Note 1)
#278
(Note 1)
#278
(Note 1)
#172
152
M901
152
155
156
158
159
153
(including CP001 (CMOS
imager)) (Note 2)
157
(Note 4)
168
160
161
(Note 3)
162
163
164
165
(Note 3)
166
(Note 3)
167
154
154
M902
A
169
(Note 5)
169
(Note 5)
169
(Note 5)
169
(Note 5)
169
(Note 5)
169
(Note 5)
169
(Note 5)
169
(Note 5)
169
(Note 5)
169
(Note 5)
169
2-1-4. LENS SECTION-2
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
151
4-436-061-01
SHEET METAL B (0020A)
152
4-439-875-01
MECHA_STOP RUBBER (0020A),
153
A-1903-090-A CM-1004 BOARD, COMPLETE (Note 2)
154
4-436-438-01
BEARING (FLANGE NON), BALL
155
4-436-060-01
SHEET METAL A (0020A)
156
8-848-901-01
DEVICE, LENS LSV-1610B
157
4-436-733-01
RUBBER (1610), SEAL (Note 4)
158
4-436-063-01
SHEET METAL D-SUB (0020A)
159
4-436-065-01
FRAME E-SUB-A (0020A)
160
4-436-068-01
FRAME F-SUB-A (0020A)
161
1-889-183-11
FP-2189 FLEXIBLE BOARD (Note 3)
162
4-436-066-01
FRAME E-SUB-B (0020A)
163
4-436-069-01
FRAME F-SUB-B (0020A)
164
4-436-070-01
ORNAMENT (0020A), FRONT
165
A-1919-696-A FP-2125 FLEXIBLE BOARD, COMPLETE (Note 3)
166
A-1919-697-A FP-2126 FLEXIBLE BOARD, COMPLETE (Note 3)
167
4-436-062-01
SHEET METAL C (0020A)
168
1-856-432-21
FILTER BLOCK, OPTICAL
169
4-441-672-01
SHEET, ADHESIVE (Note 5)
M901 1-855-222-11 MOTOR-A
(0020A)
M902 1-855-223-11 MOTOR-B
(0020A)
#172
2-178-410-01
TITE (UB TITE) 1.4
#278
4-423-712-01
SCREW, 0+P2 M2 NEW TRU-STAR (Note 1)
#288
2-187-345-21
SCREW (M1.7), P2 (Note 1)
#289
4-448-683-01
SCREW, 0+P2 M1.7 NEW TRU-STAR (Note 1)
#290
4-300-106-11
BTITE (1.4 (CH))
Screw
#172: M1.4 X 4.0 (Tapping)
(Black)
2-178-410-01
1.4
4.0
#278: M2.0 X 3.0
(Pink)
4-423-712-01
3.0
2.0
#289: M1.7 X 2.5
(Green)
4-448-683-01
2.5
1.7
#288: M1.7 X 2.5
(Black)
2-187-345-21
2.5
1.7
Note
Note 2:
Be sure to read “Precautions for Replacement of Imager”
on page 6-1 of Level 3 when changing the imager.
Note 2:
イメージャの交換時はLevel 3の6-1ページ，“イメージャ交
換時の注意”を必ずお読みください。
Note 3:
When any of these Flexible Boards is peeled off and
decreased adhesive force of the Adhesive Part or wrinkle or
break of the Flexible Board is found, replace the defective
Flexible Board with a new one.
Note 3:
これらのフレキシブル基板を剥がした場合に，粘着部の粘
着力の低下，フレキシブル基板のしわ，折れが認められた
場合は新品に交換してください。
Refer to “Assembly-3: How to distinguish the side of Optical
Filter Block facing to Lens Device”.
“Assembly-3: How to distinguish the side of Optical Filter
Block facing to Lens Device”を参照してください。
Note 1:
Machining for preventing screws from loosening is applied
to this screw.
If this screw is turned a few times or more, do not reuse it
and use a new one.
Note 1:
このねじは緩み防止加工が施されています。
2 〜 3回以上外した場合は，再利用せず新品のねじを使用
してください。
#290: M1.4 X 5.0 (Tapping)
(Black)
4-300-106-11
5.0
1.4
Note 5:
Cut the SHEET, ADHESIVE (4-441-672-01) as shown in the
balloon in the figure and use it.
Note 5:
SHEET, ADHESIVE (4-441-672-01) は図中の吹き出しのよう
に切って使用すること。
