13
Item number
Item
Parameter
Function
43
MY ADDR-1
47
IN1 AUDIO CH
48
IN1 V SETUP
51
IN2 SDI AUDIO
52
IN2 EMPHASIS
53
MY ADDR-2
57
IN2 AUDIO CH
58
IN2 V SETUP
81
LCD CONTRAST
82
LCD BACKLIGHT
91
SAVE BANK
92
RECALL BANK
93
FACTORY SET
Sets an address for the unit itself if the BKSM-T101 SDTI Input
Board is installed in the IN
1
section of the unit. When the
address matches the destination address of the input signals,
the unit receives them.
Selects the audio input signal channels to the IF OUT connector
when an optional board is installed in the IN
1
section of the
unit.
CH1/CH2: Inputs audio signals on channel 1 and 2.
CH3/CH4: Inputs audio signals on channel 3 and 4.
ALL CH1-CH4: Inputs audio signals on all channels. (When the
FEC RATE is set to 7/8, ALL CH1-CH4 is selected
automatically.)
When the BKSM-T103 Analog Input Board is installed and 3-pin
XLR connectors are used, CH1/CH2 is selected automatically
regardless of the FEC RATE selection.
Sets the VIDEO SETUP volume to be removed from the input
signals when the BKSM-T103 Analog Input Board is installed in
the IN
1
section of the unit. Select from 0.0% to 10.0% in 0.5%
steps. The parameter should be the same as that of the OUT1
V SETUP of DSM-R1 menu.
This is applicable to NTSC video signals. For PAL, only 0.0%
can be selected.
Selects the digital audio input signals if the BKSM-T102 SDI
Input Board is installed in the IN
2
section of the unit.
SDI: Digital audio signals in SDI format
AES/EBU: Digital audio signals in AES/EBU format
Turns the audio emphasis function on or off if the BKSM-T103
Analog Input Board is installed in the IN
2
section of the unit.
Sets an address for the unit itself if the BKSM-T101 SDTI Input
Board is installed in the IN
2
section of the unit. When the
address matches the destination address of the input signals,
the unit receives them.
Selects the audio input signal channels to the IF OUT connector
when an optional board is installed in the IN
2
section of the
unit.
CH1/CH2: Inputs audio signals on channel 1 and 2.
CH3/CH4: Inputs audio signals on channel 3 and 4.
ALL CH1-CH4: Inputs audio signals on all channels. (When the
FEC RATE is set to 7/8, ALL CH1-CH4 is selected
automatically.)
When the BKSM-T103 Analog Input Board is installed and 3-pin
XLR connectors are used, CH1/CH2 is selected automatically
regardless of the FEC RATE selection.
Sets the VIDEO SETUP volume to be removed from the input
signals when the BKSM-T103 Analog Input Board is installed in
the IN
2
section of the unit. Select from 0.0% to 10.0% in 0.5%
steps. The parameter should be the same as that of the OUT2
V SETUP of DSM-R1 menu.
This is applicable to NTSC video signals. For PAL, only 0.0%
can be selected.
Adjusts the contrast of the display window.
Adjusts the brightness of the display window back lighting.
Selects the menu bank in which the parameters in the current
bank are to be saved.
Selects the menu bank in which the parameters to be recalled
are saved.
Resets the parameters in the current bank to the factory setting.
0000
0000···FFFF
CH1/CH2
CH3/CH4
ALL CH1-CH4
0.0%···7.5%···10.0%
SDI
AES/EBU
OFF
ON
0000
0000···FFFF
CH1/CH2
CH3/CH4
ALL CH1-CH4
0.0%···7.5%···10.0%
1···5···10
1···5···10
1···8
1···8
---
Summary of Contents for DSM-T1
Page 18: ...18 ...
