Getting Started
11
If you have a digital component such as a
receiver (amplifier) with a digital connector, DAT
or MD
Connect the component via the DIGITAL OUT OPTICAL or
COAXIAL connector using an optical or coaxial digital
connecting cord (not supplied).
When you play a DVD, set “DIGITAL OUT” in “AUDIO SETUP”
to “ON” and then set “DOLBY DIGITAL” to “D-PCM,” “MPEG”
to “PCM” and “DTS” to “OFF” in the setup display. (page 56)
p
When using an optical digital connecting cord
Take off the cap and plug in the optical digital connecting cord.
p
When using a coaxial digital connecting cord
Notes
• Refer to the instructions supplied with the component to be
connected.
• You cannot make digital audio recordings of discs recorded in
multi-channel surround format directly using an MD deck or
DAT deck.
When you make the connections above, do not set
“DOLBY DIGITAL” to “DOLBY DIGITAL”, “MPEG” to
“MPEG” and “DTS” to “ON.” If you do, a loud noise
will suddenly come out from the speakers, affecting
your ears or causing the speakers to be damaged.
Optical digital connecting cord
(not supplied)
CD/DVD player
Receiver (Amplifier)
with a digital
connector, MD deck,
DAT deck, etc.
Coaxial digital connecting cord
(not supplied)
CD/DVD player
Receiver (Amplifier)
with a digital
connector, MD deck,
DAT deck, etc.
DIGITAL IN
COAXIAL
OPTICAL
COAXIAL
DIGITAL OUT
PCM/DTS/MPEG
DOLBY DIGITAL (AC-3)
OPTICAL
COAXIAL
DIGITAL IN
OPTICAL
DIGITAL OUT
PCM/DTS/MPEG
DOLBY DIGITAL (AC-3)
If you have an audio component with a built in
DTS decoder, Dolby Digital decoder or MPEG
decoder
Connect the component via the DIGITAL OUT OPTICAL or
COAXIAL connector using an optical or coaxial digital
connecting cord (not supplied).
p
When you play a DVD that is recorded in DTS format
Set “DIGITAL OUT” in “AUDIO SETUP” to “ON” and then
set “DTS” to “ON” in the setup display. (page 56)
p
When you play a DVD that is recorded in Dolby Digital
format
Set “DIGITAL OUT” in “AUDIO SETUP” to “ON” and then
set “DOLBY DIGITAL” to “DOLBY DIGITAL” in the setup
display. (page 56)
p
When you play a DVD that is recorded in MPEG format
Set “DIGITAL OUT” in “AUDIO SETUP” to “ON” and then
set “MPEG” to “MPEG” in the setup display. (page 56)
Notes
• Refer to the instructions supplied with the component to be
connected.
•
When you do not connect an audio component with a built
in DTS decoder, do not set “DTS” to “ON.”
•
When you do not connect an audio component with a built
in DOLBY DIGITAL decoder, do not set “DOLBY DIGITAL” to
“DOLBY DIGITAL.”
•
When you do not connect an audio component with a built
in MPEG decoder, do not set “MPEG” to “MPEG.”
Setups for the player
Some setups are necessary for the player depending on
the components to be connected.
Use the setup display to change the various settings.
For details on using the setup display, see page 47.
•
To listen to the sound through speakers connected
to a receiver (amplifier) having a digital connector or
to output the sound to a digital component such as
a DAT or MD deck
When you play a DVD, set “DIGITAL OUT” in
“AUDIO SETUP” to “ON” and then set “DOLBY
DIGITAL” to “D-PCM,” “MPEG” to “PCM” and “DTS”
to “OFF” in the setup display (page 56). These are the
default settings.
CD/DVD player
Audio component
with a built in
DTS decoder,
DOLBY DIGITAL
decoder or MPEG
decoder
Optical or coaxial digital
connecting cord
Speakers
Summary of Contents for DVP-K880D
Page 75: ...Additional Information 75 ...
