6-8
Disc Type
1. Disc Type Auto Check
2. DVD SL
12 cm
3. DVD DL
12 cm
4. CD
12cm
5. LCD
12 cm
6. DVD SL
8 cm
7. DVD DL
8 cm
8. CD
8 cm
9. LCD
8 cm
0. Reset SLED TILT
TC.---:---:--- EMG. 00
CD 12 cm
Display when CD 12cm disc was selected
[0]
Reset SLED TILT
Reset the Sled and Tilt to initial posi-
tion.
[1]
Disc Type Check
Judge automatically the loaded disc. As
the judged result is displayed at the bot-
tom of screen, make sure that it is cor-
rect.
If Disc Check Memory menu has not
been executed after EEPROM default
setting, the disc type cannot be judged.
In this case, return to the initial menu
and make a check for three types of
discs (SL, DL, CD).
[2]
to
[9]
Select the loaded disc. The adjusted
value is written to the address of se-
lected disc. No further entry is neces-
sary if
[1]
was selected.
2. Servo Control
Servo Control
1. LD
Off R. Sled FWD
2. SP
Off L. Sled REV
3. Focus
Off
4. TRK.
Off
5. Sled
Off
6. CLVA
Off
7. FCS. Srch Off
0. Reset SLED TILT
SA.------ SI.-- EMG. 00
DVD SL 12 cm
On this screen, the servo on/off control necessary for replay is
executed. Normally, turn on each servo from 1 sequentially and
when CLVA is turned on, the usual trace mode becomes active. In
the trace mode, DVD sector address or CD time code is displayed.
This is not displayed where the spindle is not locked.
The spindle could run overriding the control if the spindle system
is faulty or RF is not present. In such a case, do not operate CLVA.
[0]
Reset SLED TILT
Reset the Sled and Tilt to initial posi-
tion.
[1]
LD
Turn ON/OFF the laser.
[2]
SP
Turn ON/OFF the spindle.
[3]
Focus
Search the focus and turn on the focus.
[4]
TRK
Turn ON/OFF the tracking servo.
[5]
Sled
Turn ON/OFF the sled servo.
[6]
CLVA
Turn ON/OFF normal servo of spindle
servo.
[7]
FCS. Srch
Apply same voltage as that of focus
search to the focus drive to check the
focus drive system.
→
Sled FWD
Move the sled outward. Perform this
operation with the tracking servo turned
off.
←
Sled REV
Move the sled inward. Perform this op-
eration with the tracking servo turned
off.
3. Track/Layer Jump
Tracking/Layer Jump
1. 1Tj FWD
R. Fj (L1
→
L0)
2. 1Tj REV
L. Fj (L0
→
L1)
3. 2Tj FWD
U. Lj (L1
→
L0)
4. 2Tj REV
D. Lj (L0
→
L1)
5. NTj FWD
6. NTj REV
7. 500Tj FWD
8. 500Tj REV
9. 10k/20k FWD
0. 10k/20k REV
SA.------ SI.-- EMG. 00
DVD SL 12 cm
On this screen, track jump, etc. can be performed. Only for the
DVD-DL, the focus jump and layer jump are displayed in the right
field.
[1]
1Tj FWD
1-track jump forward.
[2]
1Tj REV
1-track jump reverse.
[3]
2Tj FWD
2-track jump forward.
[4]
2Tj REV
2-track jump reverse.
[5]
NTj FWD
N-track jump forward.
[6]
NTj REV
N-track jump reverse.
[7]
500Tj FWD
Fine search forward.
[8]
500Tj REV
Fine search reverse.
[9]
10k/20k FWD
Direct search forward.
[0]
10k/20k REV
Direct search reverse.
– The following commands are valid for DVD-DL disc only –
→
Fj (L1
→
L0)
Focus jump forward.
(Trk/Sled Servo OFF)
←
Fj (L0
→
L1)
Focus jump reverse.
(Trk/Sled Servo OFF)
↑
Lj (L1
→
L0)
Layer jump forward.
(Trk/Sled Servo ON)
↓
Lj (L0
→
L1)
Layer jump reverse.
(Trk/Sled Servo ON)
