background image

13

Important Notes on Operation

Important Notes 
on Operation

Notes on Using the 
Adapter

• The Digital Wireless Microphone 

System product must be used within a 
temperature range of 0 °C to 50 °C (32 °F 
to 122 °F).

• Operating the adapter near electrical 

equipment (motors, transformers, or 
dimmers) may cause it to be affected by 
electromagnetic induction. Keep the 
adapter as far from such equipment as 
possible.

On Cleaning

• If the adapter is used in a very humid or 

dusty place or in a place subject to an 
active gas, clean its surface as well as the 
connectors with a dry, soft cloth soon 
after use. Lengthy use of the adapter in 
such places or not cleaning it after its use 
in such places may shorten its life.

• Clean the surface and the connectors of 

the adapter with a dry, soft cloth. Never 
use thinner, benzene, alcohol or any other 
chemicals, since these may mar the 
finish.

To prevent electromagnetic 
interference from portable 
communication devices

The use of portable telephones and other 
communication devices near the 
DWA-F01D may result in malfunction 
and interference with audio signals. It is 
recommended that portable 
communication devices near the 
DWA-F01D be turned off.

Summary of Contents for DWA-F01D
















Reviews: