background image

2

Owner’s Record

The model and serial numbers are located at 
the side. Record these numbers in the 
spaces provided below.
Refer to these numbers whenever you call 
upon your Sony dealer regarding this 
product.

Model No. DWA-F01D
Serial No.

Excessive sound pressure from earphones 
and headphones can cause hearing loss.
In order to use this product safely, avoid 
prolonged listening at excessive sound 
pressure levels.

For the customers in the U.S.A.

This equipment has been tested and found 
to comply with the limits for a Class B 
digital device, pursuant to Part 15 of the 
FCC Rules. These limits are designed to 
provide reasonable protection against 
harmful interference in a residential 
installation. This equipment generates, 
uses, and can radiate radio frequency 
energy and, if not installed and used in 
accordance with the instructions, may cause 
harmful interference to radio 
communications. However, there is no 
guarantee that interference will not occur in 
a particular installation. If this equipment 
does cause harmful interference to radio or 
television reception, which can be 
determined by turning the equipment off 
and on, the user is encouraged to try to 
correct the interference by one or more of 
the following measures:

– Reorient or relocate the receiving 

antenna.

– Increase the separation between the 

equipment and receiver.

– Connect the equipment into an outlet on 

a circuit different from that to which the 
receiver is connected.

– Consult the dealer or an experienced 

radio/TV technician for help.

You are cautioned that any changes or 
modifications not expressly approved in 
this manual could void your authority to 
operate this equipment.

All interface cables used to connect 
peripherals must be shielded in order to 
comply with the limits for a digital device 
pursuant to Subpart B of Part 15 of FCC 
Rules.

This device complies with part 15 of the 
FCC Rules. Operation is subject to the 
following two conditions: (1) this device 
may not cause harmful interference, and (2) 
this device must accept any interference 
received, including interference that may 
cause undesired operation.

For the customers in Canada

This Class B digital apparatus complies 
with Canadian ICES-003.

For the customers in Europe

This product with the CE marking complies 
with the EMC Directive issued by the 
Commission of the European Community.

The manufacturer of this product is Sony 
Corporation, 1-7-1 Konan, Minato-ku, 
Tokyo, Japan.
The Authorized Representative for EMC 
and product safety is Sony Deutschland 
GmbH, Hedelfinger Strasse 61, 70327 
Stuttgart, Germany. For any service or 
guarantee matters please refer to the 
addresses given in separate service or 
guarantee documents.

WARNING

Summary of Contents for DWA-F01D
















Reviews: