background image

USA-Federal Communications Commission (FCC)

 

 

This equipment has been tested and found to comply with the limits for a Class B 

digital device, pursuant to Part 15 of FCC Rules. These limits are designed to 

provide reasonable protection against harmful interference in a residential 

installation. This equipment generates, uses, and can radiate radio frequency 

energy. If not installed and used in accordance with the instructions, it may cause 

harmful interference to radio communications. However, there is no guarantee that 

interference will not occur in a particular installation. 

 

If this equipment does cause harmful interference to radio or television reception, 

which can be determined by tuning the equipment off and on, the user is 

encouraged to try and correct the interference by one or more of the following 

measures: 

-Reorient or relocate the receiving antenna. 

-Increase the distance between the equipment and the receiver. 

-Connect the equipment to outlet on a circuit different from that to which the 

receiver is connected. 

-Consult the dealer or an experienced radio/TV technician for help. 

 

This device complies with Part 15 of the FCC Rules. 

Operation is subject to the following two conditions: 

(1) This device may not cause harmful interference, and 

(2) This device must accept any interference received, including interference that 

may cause undesired operation. 

Any changes or modifications not expressly approved by the party responsible for 

compliance could void the user’s authority to operate the equipment. 

 

Labeling 

MITSUMI WiFi MODULE DWM-W069 labelled as below. 

FCC ID: EW4DWMW069 

The label with FCC ID is to be placed on the module. If FCC ID is not visible when 

the module is installed into the system, “Contains FCC ID: EW4DWMW069” shall 

be placed on the outside of final host system.   

 

Caution: Exposure to Radio Frequency Radiation. 

To comply with FCC RF exposure compliance requirements, a separation distance 

of at least 20 cm must be maintained between the antenna of this device and all 

persons. This device must not be co-located or operating in conjunction with any 

Summary of Contents for DWM-W069










Reviews: