1-23
DXC-D30WS/P(E)/V1
Chapter 2 Fitting and Connections
32
Chapter 2
Fitting and Connections
Using the Carrying Case
Stowing the camera
Align the camera with the base of the case, and slide
the camera in forward.
Checking that the pin at the rear engages correctly,
push forward until it locks into place.
Notes
• Bring the viewfinder into the horizontal position,
slide it fully rearward and to the left, then fix before
stowing.
• When an optional microphone (ECM-670/672, C-74,
etc.) is attached, loosen the microphone fixing
screws, move the microphone to the lowest position,
and fix before stowing.
Example of fully-stowed carrying case
Align the camera with the base of the
carrying case.
Lever
Base
VCT-U14 Tripod Adaptor
Fasten straps.
LC-421 Carrying
Case
NP-1A/1B Battery Packs
(maximum two) - Fasten straps.
DXC-D30/D30P Color Video Camera
This can be stored with the following system
component fitted.
• CA-537/537P/327/327P/325A/325AP/325B
Camera Adaptor or DSR-1/1P, PVV-3/3P or
EVV-9000/9000P
• DXF-701/701CE Viewfinder
• ECM-670/ECM-672/C-74 Microphone
• Zoom lens (VCL-916BYA etc.)
(Largest lens which can be stowed is
Canon J18 X 8.5BI-B.)
• CAC-12 Microphone Holder
• CAC-4 Chest Pad
Cassettes, camera cables, etc.
Using Accessories
Chapter 2 Fitting and Connections
Chapter 2 Fitting and Connections
33
Connections
Connecting a Portable VTR
Using the optional CA-537/537P or CA-327/327P
Camera Adaptor and a camera cable, you can connect
a portable VTR. Set the VTR selector switch on the
camera adaptor according to the VTR connected.
If using a VTR from another manufacturer, consult your
Sony dealer.
Checks before making connections
Check first that the video camera, camera adaptor,
VTR, and other devices are all powered off.
Making connections
Using a camera cable, connect the VTR/CCU/CMA
connector on the camera adaptor to the camera input
connector of the VTR.
Camera cable
• Select a camera cable to fit the camera input
connector on the VTR you are using.
• The maximum camera cable extent is 10 m (33 ft).
For details, consult your Sony dealer.
Video monitor
• If using an S-VHS VTR, using a video monitor with
an S-video input connector and connecting it to the S-
video connector of the VTR will allow you to
monitor a clear picture, with no flecking.
• The output video signal from the VIDEO OUT
connector of this unit is a composite video signal.
Connect the VIDEO OUT connector of this unit to a
composite video signal input connector of the
monitor.
Setting the VTR selector switch on the
camera adaptor
When using the camera with a CA-537/537P/327/327P
Camera Adaptor, it is essential to correctly set the
VTR selector switch on the camera adaptor according
to the VTR connected. This switch determines the
type of video signal output from the VTR/CCU/CMA
connector and the audio output signal level.
Example: Connecting a BVW-50/50P Portable VTR to a CA-537/
537P Camera Adaptor
26-pin connector
VTR/CCU/CMA
DXC-D30/D30P
CCZ-A Camera Cable
26-pin connector
CAMERA IN
BVW-50/50P Portable VTR
CA-537/537P Camera
Adaptor
Example: When using a CA-537/537P
1
3
2
VTR SELECT switch
