background image

29

FCB-IX47/IX47P

FCB-IX470/IX470P

Response for command and inquiry

ACK message

: Returned by the FCB camera when it receives the command. No ACK message is returned for

inquiries.

Completion message : Returned by the FCB camera when execution of commands and inquiries is completed. In the case

of inquiry commands, it will contain reply data for the inquiry after the 3rd byte of the packet. If the

ACK message is omitted, the socket number will contain a 0.

Reply Packet

Note

Ack

X0 4Y FF

Y = socket number

Completion (commands)

X0 5Y FF

Y = socket number

Completion (Inquiries)

X0 5Y ... FF

Y = socket number

X = 9 to F: FCB camera a 8

Error message : When a command or inquiry command could not be executed or failed to be executed, the error message

is returned as instead of the completion message.

Error Packet

Description

X0 6Y 01 FF

Message length error (>14 bytes)

X0 6Y 02 FF

Syntax Error

X0 6Y 03 FF

Command buffer full

X0 6Y 04 FF

Command cancelled

X0 6Y 05 FF

No socket (to be cancelled)

X0 6Y 41 FF

Command not excutable

X = 9 to F: FCB camera a 8, Y = socket number

Socket number

When command messages are sent to the FCB camera, it is normal to send the next command message after waiting for the

completion message or error message to return. However to deal with advanced uses, the FCB camera has two buffers

(memories) for commands, so that up to two commands including the commands being executed can be received. When the

FCB camera receives commands, it notifies which command buffer was used using the socket number of the ACK message.

As the completion message or error message also has a socket number, it indicates which command has ended. Even when two

command buffers are used, the command for FCB camera management and some inquiry messages can be executed.

The ACK message is not returned for these commands and inquiries, and only the completion message of socket number 0 is

returned.

VISCA™/RS-232C

Summary of Contents for FCB-IX47





















































Reviews: