7
Basic Functions
White Balance
White Balance has the following modes, all of which
can be set using VISCA Commands.
• Auto White Balance
This mode computes the white balance value output
using color information from the entire screen. It
outputs the proper value using the color temperature
radiating from a black subject based on a range of
values from 3000 to 7500K.
This mode is the default setting.
• ATW
Auto Tracing White balance (2000 to 10000 K)
• Indoor
3200 K Base Mode
• Outdoor
5800 K Base Mode
• One Push WB
The One Push White Balance mode is a fixed white
balance mode that may be automatically readjusted
only at the request of the user (One Push Trigger),
assuming that a white subject, in correct lighting
condition, and occupying more than
1
/
2
of the image,
is submitted to the camera.
One Push White Balance data is lost when the power
is turned off. If the power is turned off, reset the One
Push White Balance.
• Manual WB
Manual control of R and B gain, 256 steps each
Automatic Exposure Mode
The variety of AE functions, which allow video signal
to output the optimum image for subjects from low
light conditions to bright light conditions, are
available.
• Full Auto
Auto Iris and Gain, Fixed Shutter Speed (NTSC:
1
/
60
s, PAL:
1
/
50
s)
• Shutter Priority
1)
Variable Shutter Speed, Auto Iris and Gain
(
1
/
1
to
1
/
10,000
s, 22 steps, std. shutter: 16 steps, slow
shutter: 6 steps)
• Iris Priority
Variable Iris (F1.4 to Close, 18 steps), Auto Gain and
Shutter speed
• Manual
Variable Shutter, Iris and Gain
• Bright
Variable Iris and Gain (Close to F1.4, 17 steps at
0 dB: F1.4, 15 steps from 0 to 28 dB)
AE – Shutter Priority
The shutter speed can be set freely by the user to a
total of 22 steps – 16 high speeds and 6 low speeds.
When the slow shutter is set, the speed can be
1
/
30
,
1
/
15
,
1
/
8
, or
1
/
4
s. The picture output is read at a normal
rate from the memory. The memory is updated at a low
rate from the CCD. AF capability is low.
In high speed mode, the shutter speed can be set up to
1
/
10,000
s. The iris and gain are set automatically,
according to the brightness of the subject.
* For AE-Manual only.
Note
The Slow Shutter function is not supported by the
FCB-IX45A/IX45AP.
AE – Iris Priority
The iris can be set freely by the user to 18 steps
between F1.4 and Close.
The gain and shutter speed are set automatically
according to the brightness of the subject.
Data
NTSC
PAL
15
10000
10000
14
6000
6000
13
4000
3500
12
3000
2500
11
2000
1750
10
1500
1250
0F
1000
1000
0E
725
600
0D
500
425
0C
350
300
0B
250
215
0A
180
150
09
125
120
08
100
100
07
90
75
06
60
50
05
30
25
04
15
12
03
8
6
02
4
3
01*
2
2
00*
1
1
Data
Setting value
Data
Setting value
11
F1.4
08
F6.8
10
F1.6
07
F8.0
0F
F2.0
06
F9.6
0E
F2.4
05
F11
0D
F2.8
04
F14
0C
F3.4
03
F16
0B
F4.0
02
F19
0A
F4.8
01
F22
09
F5.6
00
CLOSE
1) Flicker can be eliminated by setting shutter to:
t
1
/
100
s for NTSC models used in countries with a 50 Hz power
supply frequency.
.................................................................................................................................................................................................................................
t
1
/
120
s for PAL models used in countries with a 60 Hz power supply
frequency.
