Sony film imager Instructions For Use Manual Download | Manualshive

Page: 26 / 39

background image

Mis

c

e

llan

eous

Messages

26

Other Messages

When the following message appears, the ALARM
indicator does not light. The PRINT indicator blinks.

REMOVE FILM TOP
& INNER:J6

The film has jammed around the front
or inside the unit.

t

Open the top cover, then the inner
cover and remove the jammed
film.(page 28)

REMOVE FILM
TRAY:J7

The film has jammed near the film
tray.

t

Pull out the film tray and remove
the jammed film.(page 29)

REMOVE FILM
SOME PLACES:J8

The film has jammed at several points.

t

Open all of the covers and remove
the jammed film.(page 29)

CALIBRATION
INVALID

The unit takes certain measurements to
estimate a value for automatic
calibration. However, the correct value
could not actually be measured. The
unit can print, but the automatic
calibration value is not updated.

t

Try calibration again. If white strips
or scratches appear on the printout,
clean the thermal head and
rollers.(page 16)

MECHA TROUBLE
S nn

Mechanical trouble has occurred in the
sensor system of the unit.

t

Turn off the power once and then
turn it on. The unit may operate
correctly. However, if the message
still remains on the LCD, turn off
the power immediately and contact
your Sony dealer.

MECHA TROUBLE
M nn

Mechanical trouble has occurred in the
motor system of the unit.

t

Turn off the power once and then
turn it on. The unit may operate
correctly. However, if the message
still remains on the LCD, turn off
the power immediately and contact
your Sony dealer.

MECHA TROUBLE
U nn

Mechanical trouble has occurred in the
unit system of the unit.

t

Turn off the power once and then
turn it on. The unit may operate
correctly. However, if the message
still remains on the LCD, turn off
the power immediately and contact
your Sony dealer.

DICOM TROUBLE

Trouble has occurred in the DICOM
part of the unit.

t

Turn off the power immediately and
contact your Sony dealer.

TAG INVALID

Trouble has occurred in the IC tag part.

t

Turn off the power immediately and
contact your Sony dealer.

Error messages

Possible causes and remedies

Messages

Possible causes and remedies

HEAD IN COOLING
PLEASE WAIT

The thermal head has overheated.

t

Leave the unit until the head has
cools down and this message
disappears.

HEAD IN HEATING
PLEASE WAIT

The thermal head is warming up.

t

Leave the unit until the head has
warms up and this message
disappears.

PLEASE WAIT

The unit is retruning to the intial
settings to restart printing after closing
the covers which opened for removing
jammed film or cleaning.

t

Leave the unit until this message
disapperas. When this message
appears, the PRINT indicator does
not blink.

«
...
24
25
26
27
28
...
»

Summary of Contents for film imager








































Reviews:

No comments

Related manuals for film imager

Brand: NCR Pages: 224

SelfServ Checkout 7350

Brand: NCR Pages: 20

Brand: Sagem Pages: 83

Brand: Oki Pages: 99

Brand: ioCorp Pages: 18

Brand: MF DIGITAL Pages: 2

Brand: Star Pages: 82

Brand: oliser Pages: 20

Brand: Sagem Pages: 102

Brand: Novexx Solutions Pages: 6

bizhub PRO C65hc

Brand: Konica Minolta Pages: 24

Markoprint X4JET

Brand: Weber Pages: 177

Brand: Star Micronics Pages: 130

Brand: Hamlet Pages: 76

Epson Stylus NX330

Brand: Epson Pages: 63

Brand: Epson Pages: 4

Epson Stylus NX330

Brand: Epson Pages: 221

Epson Stylus NX530

Brand: Epson Pages: 251

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands