21
GB
GB
Picture/Sound Settings
For Video Input
To highlight an option and to change settings, press
F
/
f
/
G
/
g
.
Press
to confirm the selection.
The “Picture/Sound” settings include the following
options:
Picture Mode
“Vivid”:
Select for enhanced picture contrast and sharpness.
“Standard”:
Select for standard picture settings.
“Custom”:
Allows you to store preferred settings.
“Conference”:
Adjusts the picture quality for video conferencing under fluorescent
lights.
“TC Control”:
The setting is common with “Vivid”. In addition, you can use the
“True Color Control” function (after-mentioned).
Tip
To change from one “Picture Mode” option to another, you can also use PICTURE on the
remote control instead.
“Conference” may not be effective depending on the environment or the video conference
system under use. In this case, adjust the picture quality, switch to other settings of “Picture
Mode”, etc.
Picture Mode Adjust.
“Backlight”:
Adjusts to brighten or darken the screen.
“Contrast”:
Adjusts picture contrast.
“Brightness”:
Adjusts to brighten or darken the picture.
“Chroma”:
Adjusts to increase or decrease color intensity.
“Phase”:
Adjusts the color tones of the picture.
“Sharpness”:
Adjusts to sharpen or soften the picture.
“Noise Reduction”:
Select to reduce the noise level of connected equipment. Select
from “Off”, “Low”, “Mid”, “High” to set the noise level.
“CineMotion”:
Select “Auto” to optimize the screen display automatically
detecting film content. Moving picture will appear clearer and more natural looking.
Select “Off” to disable the detection.
“CineMotion” may not be correctly processed depending on the input signal pattern.
“Dynamic Picture”:
Select “On” to enhance contrast by making white brighter and
black darker.
“Gamma Correct”:
Balances the light and dark portions of pictures. Select from
“High”, “Mid”, “Low”, “DICOM GSDF Sim.” to make settings.
• You cannot set “Gamma Correct” when “Picture Mode” is set to “Conference”.
• “DICOM GSDF Sim.” can only be set when there is a DVI or HDMI input.
Gamma setting is simulated by the Grayscale Standard Display Function (GSDF) of the
Digital Imaging and Communications in Medicine (DICOM) standards. However, this
setting is for reference only and cannot be used for medical diagnosis.
“Color Temp.”:
White tone can be adjusted to suit your preference. The factory
default settings are adjusted to color temperature.
“Cool”:
Select to give the white colors a blue tint.
“Neutral”:
Select to give the white colors a neutral tint.
“Warm”:
Select to give the white colors a red tint.
“Custom”:
Enables a broader range of white tone to be set than above.
VIDEO
Note
Note
Notes
Summary of Contents for GXDL52H1 - 52" LCD Flat Panel Display
