5-10
5. REPAIR PARTS LIST
5. REPAIR PARTS LIST
DCR-HC62/HC62E_L2
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
801
2-342-624-01 SPRING (PINCH LIMITTER), EXTEN
802
X-2024-463-2 SLIDER ASSY, MODE
803
X-2024-462-3 GEAR ASSY, CAM
804
3-075-097-11 SCREW (M1.4X1.4), SPECIAL HEAD (Note 4)
805
2-342-625-01 RETAINER, LEVER EJ (Note 4)
806
2-342-621-01 GEAR, RELAY
807
3-315-414-31 WASHER
808
2-342-620-01 GEAR, CONVERSION
809
3-084-377-01 HEAD (SCREW M1.2)
810
X-2024-460-1 BASE ASSY, CAM
811
X-2024-461-1 GEAR ASSY, MODE (Note 2)
812
2-342-615-01 GEAR, NO.2
813
2-342-691-01 GEAR, NO.1
814
2-637-945-01 HOLDER, MOTOR
815
3-895-822-71 SCREW (M1.2X2), SPECIAL, 0
816
2-342-689-01 WORM SHAFT (2J)
817
2-637-947-01 BASE, MOTOR HOLDER (Note 3)
818
1-677-049-11 FP-228 FLEXIBLE BOARD (DEW SENSOR)
819
2-342-686-01 COVER, CAPSTAN
820
2-541-984-01 MIC COVER
821
3-703-816-13 SCREW (M1.4X2.0), SPECIAL HEAD
D901
6-500-652-01 DIODE GL453SE0000F (TAPE LED)
H901
8-719-067-74 ELEMENT, HOLE HW-105A-CDE-T
(S REEL SENSOR)
H902
8-719-067-74 ELEMENT, HOLE HW-105A-CDE-T
(T REEL SENSOR)
M902
X-2024-464-1 MOTOR ASSY (LOADING MOTOR)
MIC902 1-818-576-11 PIN, CONNECTOR (WITH DETECTION)
(4 PIN CONNECTOR)
Q901
6-550-672-01 TRANSISTOR PT4850FJE00F
(TAPE END SENSOR)
Q902
6-550-672-01 TRANSISTOR PT4850FJE00F
(TAPE TOP SENSOR)
S901
1-786-448-22 SWITCH, PUSH (1 KEY) (CC DOWN)
801
802
803
804
804 810
812
813
814
815
815
816
817
(Note3)
818
811
806
807
808
809
ns
ns
ns
H901
D901
Q902
S901
M902
Q901
MIC902
H902
819
820
821
FP-031
(Note1)
FP-031
(Note1)
FP-032
(Note1, 2)
Note1: The FP-031 and FP-032 are supplied as the assembled part of
the MD (N220) sub ass'y A by attaching them with the adhesive agent.
These parts are not separately supplied because assembling of
these parts requires high accuracy.
Note2: The mode switch (S903) function works when the contactor of the FP-032
contacts with the bottom surface of wiper of the mode gear ass'y.
(Note2)
Note3: When replacing the motor holder or the motor holder base, be sure to
replace them together as a pair.
Note4: Some sets do not have this screw or the EJ lever retainer.
For the sets that have them, follow the installation procedure
(3-30-2. Attachment procedure (page 40) of DV mechanical adjustment manual IX) for installation.
804
(Note4)
805
(Note4)
5-1-9. LS/MECHANICAL CHASSIS BLOCK ASSEMBLY-2
ns: not supplied