CMT-CX4iP (GB) 4-278-002-
13
(1)
Troubleshooting
1
Make sure the power cord and speaker cords are
correctly and firmly connected.
2
Find your problem in the checklist below, and take
the indicated corrective action.
If the issue persists, contact your nearest Sony dealer.
If the STANDBY indicator flashes
Immediately unplug the power cord, and check the
following items.
Are the + and
speaker cords short-circuited?
Is anything blocking the ventilation holes of the
system?
Is the iPod/iPhone connector
short-circuited?
After the STANDBY indicator
stops flashing,
reconnect the power cord, and turn on the system. If
the issue persists, contact your nearest Sony dealer.
General
The demonstration appears in the display after
plugging in the power cord even though the
system is not turned on.
Press DISPLAY
once while the system is off. The
demonstration disappears.
The system does not turn on.
Is the power cord plugged in?
The system has entered Standby mode
unexpectedly.
This is not a malfunction. The system enters Standby
mode automatically in about 30 minutes when there is
no operation or audio signal output. See “To turn off
the Automatic Standby function.”
The clock setting or the Play Timer operation
has been cancelled unexpectedly.
If about a minute elapses with no operation, the clock
setting or Play Timer setting is cancelled automatically.
Perform the operation again from the beginning.
There is no sound.
Are the + and
speaker cords short-circuited?
Are you using only the supplied speakers?
Is anything blocking the ventilation holes of the system?
The specified station may have temporarily stopped
broadcast.
Sound comes from one channel, or the left and
right volumes are unbalanced.
Place the speakers as symmetrically as possible.
Connect only the supplied speakers.
Severe hum or noise.
Move the system away from sources of noise.
Connect the system to a different wall outlet.
Install a noise filter (not supplied) to the power cord.
The remote does not function.
Remove any obstacles between the remote and the
remote sensor
on the unit, and position the unit
away from fluorescent lights.
Point the remote at the system’s sensor.
Move the remote closer to the system.
The STANDBY indicator
remains lit after
unplugging the power cord.
The STANDBY indicator
may not turn off
immediately after unplugging the power cord. The
indicator will turn off after about 40 seconds. This is not
a malfunction.
CD/MP3 player
The sound skips, or the disc will not play.
Wipe the disc clean, and replace it.
Move the system to a location away from vibration (for
example, on top of a stable stand).
Move the speakers away from the system, or place them
on separate stands. At high volume, speaker vibration
may cause the sound to skip.
Play does not start from the first track.
Return to normal play by pressing PLAY MODE
repeatedly until both “PGM” and “SHUF” disappear.
Starting playback takes more time than usual.
The following discs can increase the time it takes to
start playback;
a disc recorded with a complicated tree structure.
a disc recorded in multisession mode.
a disc that has not been finalized (a disc to which data
can be added).
a disc that has many folders.
iPod/iPhone
There is no sound.
Make sure the iPod/iPhone is connected securely.
Make sure the iPod/iPhone is playing music.
Make sure the iPod/iPhone is updated with the latest
software. If not, update the iPod/iPhone before using
with the system.
Adjust the volume.
The sound is distorted.
Make sure the iPod/iPhone is connected securely.
Turn down the volume.
Set the “EQ” setting of the iPod/iPhone to “Off” or
“Flat.”
The iPod/iPhone does not function.
If the battery of the iPod/iPhone is empty, it may not
work with this system. In such a case, recharge it with a
computer, etc. then connect it to the system.
Shut down any other iOS applications running on the
iPod/iPhone. For details, refer to the operation manual
supplied with the iPod/iPhone.
Make sure the iPod/iPhone is connected securely.
Make sure the iPod/iPhone is updated with the latest
software. If not, update the iPod/iPhone before using
with the system.
Because the operation of the system and the iPod/
iPhone are different, you may not operate the iPod/
iPhone using buttons on the remote or unit. In this
case, use the control buttons on the iPod/iPhone.
The iPod/iPhone cannot be charged.
If the battery of the iPod/iPhone is empty, the system
may not be able to charge it even if you connect it to the
system. In such a case, recharge it with a computer, etc.
then connect it to the system.
Make sure the iPod/iPhone is connected securely.
When charging an iPod/iPhone when the system is off
(Standby mode), the system does not perform charging
if the iPod/iPhone is fully charged.
The ring volume of the iPhone does not
change.
Adjust the ring volume on the iPhone.
Tuner
Severe hum or noise, or stations cannot be
received. (“TUNED” or “STEREO” flashes on the
display.)
Connect the antenna properly.
Find a location and an orientation that provide good
reception, and then set up the antenna again.
Keep the antennas away from the speaker cords and the
power cord to avoid picking up noise.
Turn off nearby electrical equipment.
To reset the system to factory settings
If the system still does not operate properly, reset the
system to factory settings.
Use buttons on the unit to reset the unit to its factory
default settings.
1
Disconnect and reconnect the power cord, and then
turn on the system.
2
Press and hold
and FUNCTION
on the unit
for 3 seconds or longer.
All user-configured settings, such as preset radio
stations, timer, and the clock, are deleted.
To turn off the Automatic Standby function
This system is equipped with an Automatic Standby
function. With this function, the system enters Standby
mode automatically in about 30 minutes when there is no
operation or audio signal output.
By default, the Automatic Standby function is turned on.
Use buttons on the unit to turn off the Automatic
Standby function.
Hold down
while the system is on, until
“AUTO STBY OFF” appears.
To turn on the function, repeat the procedure until
“AUTO STBY ON” appears.
Notes
“AUTO STBY” appears in the display for two minutes before the
system enters Standby mode.
The Automatic Standby function is invalid for the tuner function
(FM), even when you have enabled it.
The system may not enter Standby mode automatically in the
following cases;
while an audio signal is being detected.
during playback of audio tracks or files.
while the preset Play Timer or Sleep Timer is in process.
Messages
CD Over :
You have reached the end of the disc while
pressing
during playback or pause.
LOCKED :
The disc slot does not work. Contact your
nearest Sony dealer.
No Disc :
There is no disc in the player, or you have
loaded a disc that cannot be played.
No Step :
All of the programmed tracks have been
erased.
Not in Use :
You tried to perform a specific operation
under conditions where that operation is prohibited.
Not Supported :
An unsupported iPod is connected or
the iPod/iPhone whose battery is empty is connected.
Push STOP! :
You pressed PLAY MODE
during
playback in the CD function.
Step Full! :
You tried to program more than 25 tracks or
files (steps).
TIME NG! :
The Play Timer start and end times are set to
the same time.
Precautions
Discs that this system CAN play
Audio CD
CD-R/CD-RW (audio data/MP3 files)
Discs that this system CANNOT play
CD-ROM
CD-R/CD-RW other than those recorded in music CD
format or MP3 format conforming to ISO9660 Level
1/Level 2, Joliet
CD-R/CD-RW recorded in multisession that have not
ended by “closing the session”
CD-R/CD-RW of poor recording quality,
CD-R/CD-RW that have scratches or are dirty,
or CD-R/CD-RW recorded with an incompatible
recording device
CD-R/CD-RW which is finalized incorrectly
Discs containing files other than MPEG 1 Audio Layer-
3 (MP3) files
Discs of non-standard shape (for example, heart,
square, star)
Discs that have adhesive tape, paper, or sticker attached
to them
Rental or used discs with attached seals where the glue
extends beyond the seal
Discs that have labels printed using ink that feels tacky
when touched
Notes on discs
Before playing, wipe the disc with a cleaning cloth from
the center out to the edge.
Do not clean discs with solvents, such as benzine,
thinner, or commercially available cleaners or anti-
static spray intended for vinyl LPs.
Do not expose discs to direct sunlight or heat sources
such as hot air ducts, nor leave it in a car parked in
direct sunlight.
On safety
Completely disconnect the power cord (mains lead)
from the wall outlet (mains) if it is not going to be used
for an extended period of time. When unplugging the
unit, always grip the plug. Never pull the cord itself.
Should any solid object or liquid get into the system,
unplug the system, and have it checked by qualified
personnel before operating it again.
The AC power cord can be changed only by a qualified
service facility.
On placement
Do not place the system in an inclined position or in
locations that are extremely hot, cold, dusty, dirty, or
humid or lacking adequate ventilation, or subject to
vibration, direct sunlight or a bright light.
Be careful when placing the unit or speakers on
surfaces that have been specially treated (for example,
with wax, oil, polish) as staining or discoloration of the
surface may result.
If the system is brought directly from a cold to a warm
location or is placed in a very damp room, moisture
may condense on the lens inside the CD player, and
cause the system to malfunction. In this situation,
remove the disc, and leave the system turned on for
about an hour until the moisture evaporates.
On heat buildup
Heat buildup on the unit during operation is normal
and is not cause for alarm.
Do not touch the cabinet if it has been used
continuously at a high volume because the cabinet may
have become hot.
Do not obstruct the ventilation holes.
On the speaker system
This speaker system is not magnetically shielded, and
the picture on nearby TV sets may become magnetically
distorted. In this situation, turn off the TV, wait 15 to
30 minutes, and turn it back on.
If there is no improvement, move the speakers far away
from the TV.
Cleaning the cabinet
Clean this system with a soft cloth slightly moistened
with a mild detergent solution. Do not use any type of
abrasive pads, scouring powder, or solvents, such as
thinner, benzine, or alcohol.
Specifications
Main unit
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC DISTORTION:
(The United States model only)
With 8 ohm loads, both channels driven, from 120 - 15,000 Hz; rated 20 watts
per channel minimum RMS power, with no more than 10% total harmonic
distortion from 250 milliwatts to rated output.
DIN power output (rated): 15 watts + 15 watts (8 ohms at 1 kHz, DIN)
Continuous RMS power output (reference): 20 watts + 20 watts (8 ohms at
1 kHz, 10% THD)
Music power output (reference): 20 watts + 20 watts (8 ohms at 1 kHz, 10%
THD)
Input
AUDIO IN (stereo mini jack): Sensitivity 700 mV, impedance 47 kilohms
Outputs
SPEAKERS: Accepts impedance of 8 ohms
CD player section
System: Compact disc and digital audio system
Laser Diode Properties
Emission Duration: Continuous
Laser Output*: Less than 44.6µW
* This output is the value measurement at a distance of 200mm from the
objective lens surface on the Optical Pick-up Block with 7mm aperture.
Frequency response: 20 Hz
20 kHz
Signal-to-noise ratio: More than 90 dB
Dynamic range: More than 90 dB
Tuner section
FM stereo, FM superheterodyne tuner
Tuning range:
87.5 MHz
108.0 MHz (100 kHz step)
Antenna: FM lead antenna
iPod/iPhone section
Compatible iPod/iPhone models:
iPod touch 4th generation
iPod touch 3rd generation
iPod touch 2nd generation
iPod touch 1st generation
iPod nano 6th generation
iPod nano 5th generation (video camera)
iPod nano 4th generation (video)
iPod nano 3rd generation (video)
iPod nano 2nd generation (aluminum)
iPod classic
iPhone 4
iPhone 3GS
iPhone 3G
iPhone
“Made for iPod,” and “Made for iPhone” mean that an electronic accessory has
been designed to connect specifically to iPod or iPhone, respectively, and has
been certified by the developer to meet Apple performance standards. Apple
is not responsible for the operation of this device or its compliance with safety
and regulatory standards. Please note that the use of this accessory with iPod
or iPhone may affect wireless performance.
Speaker
Speaker system: 2 way speaker system, Bass reflex
Speaker units:
Woofer 80 mm (3 1/4 in.), cone type
Tweeter 40 mm (1 5/8 in.), cone type
Rated impedance: 8 ohms
Dimensions (W/H/D):
Approx. 140 mm × 245 mm × 103 mm (5 5/8 × 9 3/4 × 4 1/8 in.)
Mass: Approx. 1.2 kg (2 lb 11 oz) net per speaker
Quantity: 2 pieces (left/right)
General
Power requirements:
AC adapter
Input: 100 V
240 V AC, 50/60 Hz
Output: DC 19.5 V 3.9A
Power consumption: 24 watts
Dimensions (W/H/D) (excl. speakers):
Approx. 250 mm × 245 mm × 130 mm (9 7/8 × 9 3/4 × 5 1/8 in.)
Mass (excl. speakers): Approx. 2.2 kg (4 lb 14 oz)
Quantity of the main unit: 1 piece
Supplied accessories: Stand (1), Remote Commander (1), AC adapter (1),
Power cord (1), FM lead antenna (1), Pads for hanging on wall (1 sheet), Dock
Adapters for iPhone models (1 set)
Design and specifications are subject to change without notice.
Standby power consumption: 0.5 W
Changing the display
To
Press
Change
information on
the display
1)
DISPLAY
repeatedly when the
system is on.
Change Display
mode (see below.)
DISPLAY
repeatedly when the
system is off.
2)
1)
For example, you can view CD/MP3 disc information, such as;
track or file number
track or file name (“ ”)
artist name (“ ”)
album or folder name (“
”)
total playing time and total number of tracks on the CD-DA
disc (only when Normal Play mode is selected and the player is
stopped).
total number of folders (albums) on the MP3 disc (only when
Normal Play mode is selected and the player is stopped).
volume label if it exists on the MP3 disc (only when Normal Play
mode is selected and the player is stopped).
2)
The STANDBY indicator
on the unit lights up when the system is off.
The system offers the following display modes.
Display mode
When the system is off
1)
Demonstration
The demonstration is turned on.
Power Saving
mode
2)
The display is turned off to conserve
power. The timer and clock continue
to operate.
Clock
3)
The clock is displayed.
1)
The STANDBY indicator
on the unit lights up when the system is off.
2)
You cannot set the clock in Power Saving mode.
3)
The clock display automatically turns to Power Saving mode after
8 seconds.
Notes on the display information
Characters that cannot be displayed appear as “_”.
The following are not displayed;
total playing time for an MP3 disc.
remaining playing time, except in the case of CDDA.
The following are not displayed correctly;
elapsed playing time of an MP3 file encoded using VBR (variable
bit rate).
folder and file names that do not follow either the ISO9660
Level 1, Level 2 or Joliet in the expansion format.
The following are displayed;
remaining playing time for a CDDA disc track.
ID3 tag information for MP3 files when ID3 version 1 and
version 2 tags are used (ID3 version 2 tag information display has
priority when both ID3 version 1 and version 2 tags are used for a
single MP3 file).
Using the timers
The system offers 2 timer functions. If you use both
timers, the Sleep Timer has priority.
Sleep Timer:
You can fall asleep to music. This function works even if
the clock is not set.
Press SLEEP
repeatedly.
Play Timer:
You can wake up to CD, FM reception or iPod/iPhone
at
a preset time. Make sure you have set the clock.
1
Prepare the sound source.
Prepare the sound source, and then press VOLUME
+/
to adjust the volume.
To start from a specific CD track or audio file, create
your own program.
2
Select the timer set mode.
Press TIMER MENU
.
3
Set the play timer.
Press
/
repeatedly to select “PLAY SET?,” then
press
.
4
Set the time to start playback.
Press
/
repeatedly to set the hour, then press
. Use the procedure above to set the minutes.
5
Use the same procedure as in step 4 to set the time
to stop playback.
6
Select the sound source.
Press
/
repeatedly until the desired sound
source appears, then press
.
7
Turn off the system.
Press
. The system automatically turns on
before the preset time.
If the system is on at the preset time, the Play Timer
will not play. Do not operate the system from the time
the system turns on until the playback starts.
To check the setting
1
Press TIMER MENU
.
2
Press
/
repeatedly to select “TIMER SEL?,” and
then press
.
3
Press
/
repeatedly to select “PLAY SEL?,” and
then press
.
To cancel the timer
Repeat the same procedure as above until “TIMER OFF?”
appears in step 3, and then press
.
To change the setting
Start over from step 1.
Notes for the iPod/iPhone user
Make sure the iPod/iPhone is not playing when using the Play
Timer.
The Play Timer may not be activated depending on the status of the
connected iPod/iPhone.
Tip
The Play Timer setting remains as long as the setting is not cancelled
manually.
Playing the iPod/iPhone
1
Select the iPod function.
Press FU/
repeatedly.
2
Place the iPod/iPhone.
3
Start playback.
Press
.
To control the iPod/iPhone
To
Press
Pause playback
(pause)
/
(stop)
.
Select a track
or chapter of
audiobook/
podcast
(go back)/
(go forward)
. To fast-forward or fast-rewind,
hold down the button.
Find a point in a
track or chapter
of audiobook/
podcast
Hold down
(rewind)/
(fast
forward)
during playback, and
release the button at the desired
point.
Choose the
selected item
(enter)
.
Scroll up/down
the iPod menus
/
.
Return to the
previous menu or
select a menu
TOOL MENU
/RETURN
(return)
.
To use the system as a battery charger
You can use the system as a battery charger for an iPod/
iPhone whether the system is on or off.
The charging begins when the iPod/iPhone is placed on
the iPod/iPhone connector
. The charge status appears
in the iPod/iPhone display. When charging the iPod/
iPhone, place the iPod/iPhone on the connector with the
iPod/iPhone player stopped.
For details, see the user’s guide of your iPod/iPhone.
To stop charging an iPod/iPhone
Remove the iPod/iPhone.
Notes on charging an iPod/iPhone
If the display mode is Demonstration or Clock, you cannot charge
an iPod/iPhone even if the system is off.
If charging an iPod/iPhone when the system is off, after charging is
complete the system automatically enters Power Saving mode. The
maximum charging time while the system is off is about 4 hours.
If you press DISPLAY
while charging when the system is off,
the system stops charging an iPod/iPhone. To restart charging of an
iPod/iPhone, reconnect the iPod/iPhone when the display mode is
Power Saving mode.
Notes
If the battery of the iPod/iPhone is empty, the system may not
recognize it. In such a case, recharge it with a computer, etc. then
connect it to the system.
The performance of the system may be vary, depending on the
specifications of your iPod/iPhone.
When placing or removing the iPod/iPhone, handle the iPod/iPhone
in the same angle as that of the iPod/iPhone connector on the unit
and do not twist or sway the iPod/iPhone to prevent connector
damage.
Do not carry the unit with an iPod/iPhone set on the connector.
Doing so may cause a malfunction.
When placing or removing the iPod/iPhone, brace the unit with one
hand and take care not to press the controls of the iPod/iPhone by
mistake.
Before disconnecting the iPod/iPhone, pause playback.
Hold down
/
to fast-forward (fast-rewind) while
playing video if
/
does not function.
When the iPhone is connected to the system and you receive a call
during playback, playback will pause and you can take an incoming
call.
To change the volume level, use /
. The volume level
does not change if you adjust it on the iPod/iPhone.
This system is designed for iPod/iPhone only. You cannot connect
any other portable audio players.
To use an iPod/iPhone, refer to the user’s guide of your iPod/iPhone.
Sony cannot accept responsibility in the event that data recorded to
iPod/iPhone is lost or damaged when using an iPod/iPhone with
this unit.
Using optional audio components
1
Prepare the sound source.
Connect additional audio component to the AUDIO
IN jack
on the unit using an audio analog cord
(not supplied).
2
Turn down the volume.
Press VOLUME
.
3
Select the AUDIO IN function.
Press FU/
repeatedly.
4
Start playback.
Start playback of the connected component and adjust
the volume.
Note
The system may enter Standby mode automatically if the volume
level of the connected component is too low. Adjust the component’s
volume accordingly. See “To turn off the Automatic Standby function.”
Adjusting the sound
To
Press
Adjust the volume /
.
Generate a more
dynamic sound
(Dynamic Sound
Generator X-tra)
DSGX
on the unit.
Set the sound
effect
EQ
repeatedly to select “BASS”
or “TREBLE,” and then press
/
to adjust the level.
