2
HCD-DZ100
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
•
Unleaded solder melts at a temperature about 40
°
C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°
C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
•
Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
Notes on chip component replacement
•
Never reuse a disconnected chip component.
•
Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
•
Keep the temperature of the soldering iron around 270
°
C
during repairing.
•
Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
•
Be careful not to apply force on the conductor when soldering
or unsoldering.
Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
This appliance is classified as
a CLASS 1 LASER product.
The CLASS 1 LASER
PRODUCT MARKING is
located on the rear exterior.
Video section
Outputs
Video: 1 Vp-p 75 ohms
S video:
Y: 1 Vp-p 75 ohms
C: 0.286 Vp-p 75 ohms
COMPONENT:
Y: 1 Vp-p 75 ohms
P
B
/C
B
, P
R
/C
R
: 0.7 Vp-p
75 ohms
Video: 1 Vp-p 75 ohms
R/G/B: 0.7 Vp-p 75 ohms
(EXCEPT AEP, UK, RU)
(AEP, UK, RU)
Antenna (aerial)
AM loop antenna (aerial)
Intermediate frequency
450 kHz
Middle eastern models:
531 – 1,602 kHz (with the
interval set at 9 kHz)
Other models:
530 – 1,710 kHz (with the
interval set at 10 kHz)
531 – 1,602 kHz (with the
interval set at 9 kHz)
General
Power requirements
North American and Mexican models:
120 V AC, 60 Hz
Central/South American models:
110 – 240 V AC, 50/60 Hz
Taiwan model:
12
Korean model:
220 V AC, 60 Hz
0 V AC, 50/60 Hz
Other models:
220 – 240 V AC, 50/60 Hz
Power consumption
On: 135 W
Standby: 0.3 W (at the
Power Saving mode)
Dimensions (approx.)
430 70 295 mm
(17 2
7
/
8
11
5
/
8
inches)
(w/h/d) incl. projecting
parts
Mass (approx.)
3.6 kg (7 lb 15 oz)
Design and specifications are subject to change
without notice.
×
×
×
×
MODEL IDENTIFICATION
– Rear Panel –
Part No.
2-588-951-0
[]
2-588-951-1
[]
2-588-951-2
[]
2-588-951-3
[]
2-588-951-4
[]
AUS model
2-588-951-5
[]
KR model
2-588-951-6
[]
E32 model
2-588-951-7
[]
MX model
2-588-951-9
[]
US model
2-634-883-1
[]
• Abbreviation
AUS
: Australian model
CND
: Canadian model
E32
: 110-240V AC area
in E model
EA
: Saudi Arabia model
KR
: Korean model
MX
: Mexican model
RU
: Russian model
SP
: Singapore model
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
