2-17 (E)
.
IM/HDCU1000 Series
2-3. Audio System
2-3-1. Setting the Intercom System
HDCU1000/1080/1500 can be connected to the intercom
lines (producer line and engineer line) of the two indepen-
dent systems and can switch them.
The intercom systems conforming to HDCU1000/1080/
1500 are 4W, RTS and Clear-Com. The internal switches
of the unit need to be set according to the system used.
AVP-6 board (A side/panel side)
1. Selecting the intercom system
Select a system (4W, RTS or Clear-Com) respectively for
the engineer line and the producer line according to the
system used. Then, select the number of intercom line
systems (1CH or 2CH).
.
Selecting the producer line
:
Set switches S602/600 (PROD SELECT) on the AVP-6
board according to the system used.
Factory setting : 4W (S602)
RTS (S600)
.
Selecting the engineer line
:
Set switches S603/601 (ENG SELECT) on the AVP-6
board according to the system used.
Factory setting : 4W (S603)
RTS (S601)
.
When the intercom line is 1 channel
:
Set 1CH at INCOM-CH on page “C05”
*
of the configu-
ration menu. In this setting, the intercom line is connect-
ed to the producer line of HDCU1000/1080/1500.
When the switch is set in this position, connection of the
intercom line of the unit is fixed to the producer line
regardless of the setting of the INCOM PROD/ENG
switch of the HDC1000 series and the INCOM SELECT
switch on the front panel of the unit.
.
When the intercom line is 2 channels
:
Set 2CH at INCOM-CH on page “C05”
*
of the configu-
ration menu.
Factory setting : 2CH
Adjusting the RTS cancel
When the RTS intercom system is used, the following
adjustment also needs to be made.
(1) Connect a headset to the INCOM connector on the
front and perform the procedure described in the follow-
ing paragraph “2. Setting the headset microphone”.
(2) Set
_
99 for the value of SIDE TONE on page “C05”
*
of the configuration menu.
(3) Set the INCOM SELECT switch on the front panel to
PROD.
(4) Speak into the microphone of the headset and adjust
the 2WIRE CANCEL PROD control of the AVP-6
board panel to minimize the side tone.
(5) Set the INCOM SELECT switch on the front panel to
ENG.
(6) Speak into the microphone of the headset and adjust
the 2WIRE CANCEL ENG control of the AVP-6
board panel to minimize the side tone.
(7) Return the value of SIDE TONE on page “C05”
*
of
the configuration menu to its original value or to the
desired value of user.
n
When setting S602 and S603 to RTS, be sure to connect
them to the RTS system. Otherwise, they oscillate and
have adverse effects on the peripheral circuits.
*
: “C06” in software V1.10 or later
AB
C
D
E
F
G
1
2
3
4
5
S603
S602
S600
S601
RV501
RV500
S501
S500
S503
S502
S12
S11
S22 S32
S21 S31
AV
P
/1.001
LINE
DELA
Y
CCU
PO
WER
CAM
LOCK
CAM PO
WER
SYSTEM
ON/
OFF
PR
OD
ENG
2WIRE CANCEL
2WIRE CANCEL PROD control
2WIRE CANCEL ENG control
CAMERA POWER switch
1 1
J
