19
Displaying the focus assist indicators
The focus assist indicator function extracts the irregularities of
a subject and converts the integrated values to a level
indicator, which shows the focus condition.
The focus setting where the indicator shows the maximum
level is the best focus setting. (The range of the indicator
substantially changes depending on picture elements or
shooting environments. Adjust it with GAIN and OFFSET as
required.)
1
Display the CONTENTS page of the OPERATION
menu (referring to steps 1 to 4 in “Adding the VF
detail signal”).
2
Turn the MENU SEL knob/ENTER button to align the
arrow marker (
,
) to <FOCUS ASSIST> and press the
MENU SEL knob/ENTER button.
The <FOCUS ASSIST> page is displayed.
3
Turn the MENU SEL knob/ENTER button to align the
arrow marker (
,
) to the item to be set and press the
MENU SEL knob/ENTER button.
To use the level indicator
Setting INDICATOR to ON displays the level indicator on
a viewfinder. You can set the display format with the menu
items below.
MODE:
Set the type and position of the indicator.
LEVEL:
Set the density and the response speed of the
indicator.
GAIN:
Set the sensitivity of the indicator.
1)
OFFSET:
Set the offset of the focus detection value.
2)
1) Normally, the sensitivity of the indicator is automatically set to
the optimum value in conjunction with the AREA MARKER
SIZE set value. Use this setting when an optimum sensitivity
value cannot be obtained, depending on the shooting
environment.
2) Normally, the optimum offset is automatically set in conjunction
with the AREA MARKER SIZE and MASTER GAIN set values.
Use this setting when the optimum offset cannot be obtained,
depending on the shooting environment.
To use the area marker
Setting AREA MARKER to ON displays the detection area
of the focus as a marker on a viewfinder screen.
You can set the size and position of the detection area with
the menu items below.
SIZE:
The size of the detection area can be changed. (If
the area size is too large, both the subject and the
background are included in the area, making the
indicator display may easily deviate from the
subject.)
POSITION:
Roughly set the position of the detection area.
POSITION H:
Finely adjust the position of the detection
area in the horizontal direction.
POSITION V:
Finely adjust the position of the detection
area in the vertical direction.
4
Turn the MENU SEL knob/ENTER button to display
the desired setting and press the MENU SEL knob/
ENTER button.
5
To finish the adjustment, set the DISPLAY switch to
OFF to exit Menu mode.
• The level indicator and the effect area marker cannot be
displayed simultaneously. Whichever you set to ON last is
preferentially displayed.
• The area marker and the aspect safety marker cannot be
displayed simultaneously. Whichever you set to ON last is
preferentially displayed.
• When displaying the focus assist indicators, check that the
flange focal length has been precisely adjusted.
For details about the flange focal length, see “Adjusting the
Flange Focal Length” (page 10).
Setting the Focus Position Meter
Function
The focus position meter function allows you to graphically
display the registered focus position (marker) and the current
focus position (index) graphically on the viewfinder screen.
You can set the focus to the registered point easily by
adjusting the focus until the index position overlaps the marker
position (adjusted state). In the adjusted state, you can display
a color frame and marker name on the viewfinder screen.
1
Display the CONTENTS page of the OPERATION
menu (referring to steps 1 to 4 in “Adding the VF
detail signal”).
Level indicator (its position and operations can be adjusted.)
Area marker to display the detection area of the
focus (its size and position can be adjusted.)
<FOCUS ASSIST> 07 TOP
INDICATOR : OFF
MODE : BOX BOTTOM
LEVEL : 3 QUICK
GAIN : 50
OFFSET : 50
AREA MARKER: ON
SIZE : MIDDLE
POSITION : CENTER
POSITION H: 50
POSITION V: 50
Notes
NEAR
FAR
Current focus position (index)
Registered focus position (marker)
