6
Controls and Connectors
Front right
a
INCOM1 (intercom 1) button
The intercom 1 microphone is turned ON while this button is
held pressed.
You can also assign other functions to this button, using the
menu displayed on the viewfinder screen.
b
RET 1 (return video 1) button
The return video 1 signal from the camera control unit is
monitored on the viewfinder screen while this button is
pressed. It functions the same as the RET 1 button on the side
and RET/ASSIGNABLE button A on the operation
panel on the rear of the camera
You can also assign other functions to this button, using the
menu displayed on the viewfinder screen.
c
Assignable switch
You can assign a function using the menu displayed on the
viewfinder screen.
You can also display the assigned function name by attaching
the corresponding label (supplied) for the assigned function.
d
Filter select buttons
You can switch the built-in ND and CC (color temperature
conversion) filters by pressing the select buttons while holding
the FILTER LOCAL button depressed.
Pressing the left button selects the available ND filters
(CLEAR, 1/4ND, 1/8ND, 1/16ND,1/64ND) in sequence.
Pressing the right button selects the available CC filters
(cross, 3200K, 4300K, 6300K) in sequence.
e
FILTER LOCAL button
While holding this button depressed, press either of the filter
select buttons to select the built-in optical filters.
f
AUTO W/B BAL (white and black balance automatic
adjustment) switch
To automatically adjust white and black balance when the
camera is used in standalone status without connecting to the
camera control unit.
WHT:
Automatically adjust white balance.
BLK:
Automatically adjust black balance.
g
GAIN switch
To select the master gain of the video amplifier based on
lighting conditions when the camera is used in standalone
status without connecting a camera control unit.
When shipped from the factory, the values set are L = 0 dB,
M = 6 dB, and H = 12 dB.
h
OUTPUT (output signal selection)/AUTO KNEE switch
To select the signal (color bar signal or camera’s video signal)
to be used as output to the viewfinder or a video monitor when
the camera is used in standalone status without connecting a
camera control unit.
When the camera’s video signal is being used as output, the
auto knee function may be used.
The relationship between the switch setting and the output
signal and auto knee function is shown in the table below.
i
WHITE BAL (white balance memory selection) switch
To select the white balance adjustment method or the memory
used to store the adjusted value when the camera is used in
standalone status without connecting a camera control unit.
PRST (preset memory):
White balance is adjusted to a
preset value corresponding to a color temperature of
3200K.
A or B:
Selects memory A or B.
j
DISPLAY switch
The functions of the DISPLAY switch are as follows:
DISPLAY:
Characters and messages showing the camera
settings and operating status may be displayed on the
viewfinder screen.
OFF:
Status messages will not appear on the viewfinder
screen.
MENU:
Menus for camera settings will be displayed on the
viewfinder screen.
k
STATUS/CANCEL switch
STATUS:
When no menu is displayed on the viewfinder
screen, the status information of this camera is displayed.
CANCEL:
When a menu is displayed on the viewfinder
screen, you can cancel any changed settings or return
the display to the previous menu.
l
MENU SEL (menu select) knob/ENTER button (rotary
encoder)
To select settings from menus displayed on the viewfinder
screen (by rotating the knob) and to confirm settings (by
pushing the button).
You can change the ECS frequency by pushing the ENTER
button when no menu is displayed on the viewfinder screen.
Make sure that the camera is used in standalone status
without connecting a camera control unit, and the shutter
mode is set to ECS. When the camera is used in standalone
status and the shutter mode is set to other than ECS, the VF
DETAIL function can be adjusted.
When a camera control unit or a remote control device, such
as an MSU or RCP, is connected, the functions of
6
to
9
are
a
b
c
d
e
f
g
h
i
j
k
l
OUTPUT
AUTO KNEE Function
BARS
OFF
Output is a color bar signal.
CAM
OFF
Output is the camera’s video signal. The
auto knee circuit is disabled.
CAM
ON
Output is the camera’s video signal. The
auto knee circuit is enabled.
Note
